CHYBA! NA POUŽITIE ŠTÝLU TITRE 1 NA TEXT, KTORÝ SA MÁ ZOBRAZIŤ NA TOMTO MIESTE, POUŽITE KARTU DOMOV.
CHYBA! NA POUŽITIE ŠTÝLU TITRE 2 NA TEXT, KTORÝ SA MÁ ZOBRAZIŤ NA TOMTO MIESTE, POUŽITE KARTU DOMOV.
CHYBA! NA POUŽITIE ŠTÝLU TITRE 3 NA TEXT, KTORÝ SA MÁ ZOBRAZIŤ NA TOMTO MIESTE, POUŽITE KARTU DOMOV.
c) Etalonnage de la consigne vitesse fil
Calibration of wire speed setting
Passer en mode "SETUP"
Afficher la ligne
Vf RAPIDE DEVIDAGE : xx,x m/mn
et relever cette vitesse
Afficher la ligne
Vf LENTE DEVIDAGE : xx,x m/mn
et relever cette vitesse
Afficher la ligne
REGLAGE Vf DEVIDAGE : xxx
la valeur est à ajuster entre 220 et 250 par la
procédure suivante :
mesurer au volmètre numérique la
consigne U.Vf
soit entre PT2 (+) et PT1 (-) sur la
carte INTERFACE DEVIDAGE
soit entre PT3 (+) et PT4 (-) du
VARISAF 21
actionner l'entrée "DEVIDAGE" (B8 de
P1 ou D3 de P2 ou A5 de P3) et
attendre 7s la fin de la montée en
vitesse rapide
régler en face-avant par le potentiomètre
pour avoir
U.Vf = Vf RAPIDE / 2
Afficher la ligne
REGLAGE Vf RELEVAGE : xx
la valeur est à ajuster entre 01 et 20 par la
procédure suivante :
actionner l'entrée "RELEVAGE" (A8 de
P1 ou C3 de P2 ou B5 de P3)
régler en face-avant par le potentiomètre
pour avoir
-U.Vf = Vf LENTE / 2
450 /
450
STARMATIC A
R
sortie
sortie
sortie
( 10V 20,0 m/mn )
sortie
( -5V 10,0 m/mn )
Switch to "SETUP" mode
Display the line
FAST FEEDING W-SPEED :
and record this speed
Display the line
LOW FEEDING W-SPEED:
and record this speed
Display the line
W-SP. FEEDING ADJUSTMENT:
the value is to be set between 220 and 250
according to the following procedure:
measure the U.Vf setting on the digital
voltmeter
either between PT2 (+) and PT1 (-)
on the WIRE-FEED INTERFACE
board
or between PT3 (+) and PT4 (-) of
the VARISAF 21
actuate the "WIRE-FEED" input (B8 of
P1 or D3 of P2 or A5 of P3) and wait 7s
for the end of the fast speed build-up
adjust in front panel via the
potentiometer in order to have
U.Vf = Vf FAST / 2
Display the line
W-SP. REWINDING ADJUST.:
the value is to be set between 01 and 20
according to the following procedure:
actuate the "RAISING" input (A8 of P1 or
C3 of P2 or B5 of P3)
adjust in front panel via the
potentiometer in order to have
-U.Vf = Vf LOW / 2
xx,x m/mn
output
xx,x m/mn
output
xxx
output
( 10V
20,0 m/mn )
xx
output
( -5V
10,0 m/mn )
- 91
C