INNOMARK beta Notice D'utilisation page 16

EN – Operating Manual
1. For a manual test you start the device like described
above.
2. As soon as you see "rdY" on the display, push the left
button.
3. The manual test mode will start and you will see a flashing
"rdY" indicating that you can now start blowing into the unit.
4. Start blowing steadily into the mouthpiece for 4 seconds,
the device will beep continuously during the test. Tip: Blow
as if you were whistling without a sound (but without pause).
Continue blowing and do not stop until you hear a double
beep, then the test is successfully completed.
5. After a successful test, the device analyses the breath
sample, you will see „C.---". (= „Calculate") on the display.
After a short while you will hear 2 beeps and the test result
will be displayed (with 4 digits and 3 decimal places) in per
mill (‰ = g/L).
Note: It is recommended to wait at least 5 minutes between
two tests to avoid overloading the sensor and to maintain
the quality of the sensor for as long as possible. If it is not in
use the device will turn off automatically after 30 seconds,
additionally you hear 1 beep tone. If you want to conduct a
new test, please press the power button. You can turn off the
device manually if you constantly press the power button
for 3 seconds.
TEST RECORD MEMORY MODE
Recall cumulative test count
Shortly press the "Power" button (1x) during the countdown,
so you can display the cumulative test count – the number
of all tests which were done so far. This number also helps
you to check if a calibration service is needed (see chapter
"Calibration" for more details). You can reset this counter
(which is not recommended) if you press the left button until
the counter is reset to zero.
Recall previous test results (up to 16 records)
Shortly press the "Power" button (2x) during the countdown,
so you can display the latest test results (beginning with
the last test). First you see the test number and then the test
result saved with this number. If you press the left button
you can see the next saved test number followed by the
21
test result. If you want to see the saved results ion backward
order, press he right button. If you want to leave the test
record memory mode and go back to the countdown, then
shortly (1x) press the "Power" button.
ACE INSTRUMENTS RECOMMENDS
• Always use a new mouthpiece for each person and
test that is conducted. ACE Instruments assumes no
liability for any damages that may arise when several
people use the same mouthpiece for multiple tests.
• Only use the provided individually packaged
and hygienic mouthpieces. During each test the
breathalyzer' s internal and external parts come into
contact with human secretion (saliva, blood, sweat, etc.)!
• Use safety gloves when pulling out a mouthpiece
used by another person! You can buy appropriate
gloves at ACE Technik (www.ace-technik.de).
IMPORTANT NOTICE
• WHEN YOU HAVE EATEN, DRUNKEN ALCOHOL
OR SMOKED A CIGARETTE, WAIT AT LEAST
15 MINUTES BEFORE STARTING THE
MEASUREMENT. ANY TEST CONDUCTED PRIOR
TO THE EXPIRATION OF THE RECOMMENDED
WAITING PERIOD WILL RESULT IN INACCURATE
RESULTS.
• IF THE TEST RESULT IS BELOW 0. 1 0‰ (PER MILL
= g/L) OR 0.010% BAC (US setting) OR 0.050mg/L
(UK settting) THEN THE DEVICE SHOWS 0.00 (‰
OR % BAC OR mg/L – depending on the setting)
ON THE DISPLAY. THIS HAPPENS BECAUSE AT A
LOW RANGE OF ALCOHOL CONCENTRATION IT
IS POSSIBLE TO MEASURE OTHER MATERIALS IN
YOUR MOUTH.
• This breathalyzer is a high quality and sensitive
measurement device. To maintain the accuracy of
the sensor, it should regularly be used. If the device is
not used for an extended period of time, the sensor
can dry out. ACE Instruments recommends using the
breathalyzer at least 2 times per month (even if you
have not been drinking alcohol).
22