CAME SELT1W4G Mode D'emploi page 7

- Enter the INSTALLER PASSWORD + (#)
- Enter 3 + (#)
- Enter a USER COMBINATION (from two to
eight figures) + (#)
- Repeat the USER COMBINATION + (#)
- Waitfor the sound signal
- Save the radio-frequency code into the
operator.
ADVANCED procedure
The position in the memory and the
radio-frequency code need to be entered ma-
nually (25 USER COMBINATIONS, maximum).
- Enter the INSTALLER PASSWORD + (#)
- Enter 4 + (#)
- Enter a USER COMBINATION (from two to
eight figures) + (#)
- Re-enter the USER COMBINATION + (#)
- Specify the position in the memory where
it will be saved: from (1) to (25) + (#).
- Enter 1 + (#)
- Select the code: 1 (or 2, 3, 4) + (#)
- Waitfor the sound signal
- Save the radio-frequency code into the
operator.
Using the internal, fixed
radio-frequency code
- Enter the INSTALLER PASSWORD + (#)
- Enter 4 + (#)
- Enter any USER COMBINATION of two to
eight fi gures + (#)
- Re-enter the USER COMBINATION + (#)
- Specify the position in the memory where
it will be saved: from (1) to (25) + (#).
- Enter 2 (12 bit) / 3 (24 bit) + (#)
- Select code 1 (or 2, 3, 4) + (#)
- Wait for the sound signal
- Save the radio-frequency code into the
operator.
Other settings
Edit INSTALLER PASSWORD
- Enter the INSTALLERPASSWORD + (#)
+ 1 + (#)
- Enter the new password + (#) (three to
eight figures)
- Re-enter the new password + (#)
- Wait for the sound signal
Restoring factory settings
- With one hand, hold down both control
cards, and with the other remove the
battery
- press and keep pressed the (#) key
- fit the battery and wait 5 seconds for the
sound signal
Restoring the 555 installer password
- With one hand, hold down both control
cards, and with the other remove the
battery
- press and keep pressed the (*) key
- fit the battery and wait for the sound
signal (about 5 seconds)
Editing USER COMBINATIONS
- Press (*) + (#)
- enter the USER COMBINATION + (#)
- enter the new USER COMBINATION + (#)
- re-enter the new USER COMBINATION
+ (#)
- wait for the sound signal
Removing users
- Enter the INSTALLERPASSWORD + (#)
+ 7 + (#)
- enter the position between 01 and 25
+ (#)
- repeat the position + (#)
- wait for the sound signal
Removing ALL users
- Enter the INSTALLERPASSWORD + (#)
+ 7 + (#)
- enter 00 + (#)
- repeat 00 + (#)
- wait for the sound signal
Saving on Memory Roll (if fitted)
- Enter the INSTALLERPASSWORD + (#)
+ 5 + (#)
- wait for the sound signal
Restoring from Memory Roll (if fitted)
- Enter the INSTALLERPASSWORD + (#)
+ 6 + (#)
- wait for the sound signal
System options
- Enter the INSTALLERPASSWORD + (#)
+ 0 + (#)
- press the key of the function you want
(see table) + (#)
- set the value you want (see table) + (#)
- wait for the sound signal
Key Function Value
Block for 1
0 = OFF /
2 minute (after
1 = ON (default)
five errors)
LED bright- 1, 2, 3 (default),
3
ness 4, 5
0 = OFF /
1 = ON /
Activating the
4 2 = press any
backlighting
key for three
seconds (default)
0 = 0 dBm /
1 = 5 dBm /
Transmitting
5 2 = 7 dBm
power
(default) /
3 = 10 dBm
Replacing the battery
Battery ALMOSTflat: Three flashes from the
LED any time a key is pressed. With backli-
ghting on: only the center LED turns on.
Flat BATTERY: the LEDs flash three times
and the sound signal sounds off three
times, simultaneously. - The keypad is no
longer usable.
- Strip the frame
- With one hand, hold down both control
cards, and with the other remove the
battery; replace the battery with the right
type and respect the polarities shown on
the control card. ❹
DISMANTLING AND DISPOSAL - The packaging materials
(cardboard, plastic, and so on) should be disposed of as
solid household waste. Separate and properly dispose of
the device components, that is, metals, control boards,
batteries, and so on. Check your local laws to properly
dispose of the materials.
DISPOSE OF RESPONSIBLY!
The contents of this manual may be changed at any time
without prior notice.
The measurements, unless otherwise stated, are in mil-
limeters.