Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
General Precautions
Before installing, carefully read the instructions
and follow the process explained by the manu-
facturer.
Installing, programming, commissioning and
maintenance of this device must be only done
by qualified, specifically trained technicians,
and in full compliance with any applicable re-
gulatory provisions, including workplace safety
and waste disposal standards and regulations.
Before carrying out any cleaning or maintenan-
ce operation, disconnect the device from the
power supply.
The equipment must be destined solely for the
use for which it was expressly designed.
The manufacturer can not be held liable for any
damage resulting from improper, unreasonable,
and/or erroneous use.
Install in state-of-the-art fashion, so that the
casing remains clean and watertight.
Description
Radio-frequency, 433.92 MHz SELT1W4G
and 868.35 MHz SELT1W8G surfa-
ce-mounted keypad selector, featuring 25
savable USER COMBINATIONS, and instal-
ler password for accessing the program-
ming mode. Compatible with fixed-code
CAME transmitters.
Description of parts
① Casing
② Gasket
③ Inner frame
④ Keypad
⑤ Fastening screws
⑥ Front cover
⑦ Memory Roll Card
⑧ Battery
Dimensions (mm)
Technical data
SELT1W4G /
Type
SELT1W8G
Protection rating (IP)
54
3 (one CR123A
battery for a
Power supply (V)
minimum of
1600mAh).
Maximum draw (mA)
48
Maximum
144
consumption (mW)
Range in open field
0.5 min. / 80*
(m)
max.
USER COMBINATION
2 min. - 8 max.
fi gures
Figures INSTALLER
3 min. - 8 max.
PASSWORD
Number of
111,111,100
combinations
Operating temperature
-20 to +55
(°C)
Apparatus class
III
* ⚠ if the keypad is installed onto metal
parts, the range will decrease.
1
Average battery life: 24 months with
backlighting on / 48 months with backli-
ghting off.
Installing
Drill the holes marked on the back of the
casing. ❶
Fasten the casing by using suitable screws
and plugs. ❷
Place the gasket and fasten the inner frame.
❸
Fit the battery and fasten the base to the
keypad. ❹
Fit the selector into the casing and fasten it
by using the supplied screws. ❺
Attach the front cover to the selector. ❻
To remove the front cover, use a screw-
driver as a lever.
Operation
The keypad replicates the operation of the
1
transmitters; the radio-frequency code is
sent by entering a programmable numerical
sequence (USER COMBINATION), followed
by the confi rmation key: # (e.g.: 1932#).
A FIXED-CODE TRANSMITTER CAN
EITHER ACQUIRE A RADIO-FREQUENCY
CODE OR USE THE FOUR INTERNAL CO-
DES (12 BIT, 24 BIT OR ROLLING CODE).
Entering a wrong code fi ve times in a row,
will block the selector for one minute (this is
the default setting).
To access the programming mode, enter the
INSTALLER PASSWORD (the default one
is 555#).
The 555 numerical sequence cannot be
used as a USER COMBINATION.
During programming, the backlighting is
intermittent.
The (*) key CANCELS any procedure that is
underway.
The INSTALLER PASSWORD and the USER
COMBINATION must be diff erent.
Pressing any key for three seconds will
activate the backlighting.
⚠ When the memory is full, the device
emits four consecutive sound signals.
Self-learning from a fixed-code
transmitter
BASIC procedure
The position in the memory is automati-
cally managed by the system - there are up
to FOUR USER COMBINATIONS available.
- Enter the INSTALLER PASSWORD + (#)
- Enter 2 + (#)
- Enter a USER COMBINATION (from two to
eight figures) + (#)
- Repeat the USER COMBINATION + (#)
- Send the code from the transmitter that is
already memorized in the operator (within
10 s). ❼
- Waitfor the sound signal.
ADVANCED procedure
The position in the memory needs to be
manually entered - there are up to 25 USER
COMBINATIONS.
- Enter the INSTALLER PASSWORD + (#)
- Enter 4 + (#)
- Enter a USER COMBINATION (from two to
eight figures) + (#)
- Repeat the USER COMBINATION + (#)
- Specify the position in the memory where
it will be saved: from (1) to (25) + (#).
- Enter 4 + (#)
- Send the code from the transmitter that is
already memorized in the operator (within
10 s). ❼
- Waitfor the sound signal
Using the internal Rolling Code
radio-frequency code
BASIC procedure
The position in the memory and the ra-
dio-frequency code are processed automati-
cally (Four USER COMBINATIONS, maximum).
Publicité
