Publicité
Les langues disponibles
Les langues disponibles
Configuration
Once the system is correctly assembled and connected to a power
source, you may need to configure the controller's software.
Switch the On/Off switch to On.
After 5 seconds the SPX splash screen will be displayed for 5 seconds.
This will be followed by the welcome screen:
•
Check that the date and time are correct and that the correct video
standard for your country (PAL or NTSC) is displayed.
•
Check that the correct reel size is set.
•
If a USB Flash Drive or CF card is present, check that the correct
memory parameters are displayed (if both a USB drive and CF card
are present then only the USB drive parameters will be displayed).
Press OK or Enter to continue.
If required you can set up the correct reel type, date, time and language
as follows:
To navigate through the system software use the keypad or keyboard
function and arrows keys. Use the
Use the
and
keys to scroll through the various options and press OK
to accept the selection.
Select the correct reel
Select "Menu" (F1 key) to go to the main menu screen, select "Setup" and
press OK.
Select "Reel", press OK to continue to the Reel Setup Menu.
Use the
or
keys to select the correct reel length and type, press OK
to confirm your choice.
Press
to exit the Reel Setup Menu.
Basic Controller Set-up
From the main Setup Menu, select "Controller" and press OK .
Select "Basic Settings" and press OK.
Select the setting you wish to edit and press OK or Enter.
Use the keyboard to modify Time or Date and use the
scroll through the various options.
Press OK to accept the new settings.
When all the required settings have been setup, press F6 to exit to the
top-level screen.
TFT Screen Settings
The screen brightness and contrast functions are available on the top
level screen.
Press BRI (F5) to set the Screen Brightness or CONTR (F6) to set the
Screen Contrast.
Use the
and
keys to set the desired value and press OK to accept
your settings.
key to return to the previous menu.
and
keys to
10
Jobs
By entering information about your current session Client, Site and Survey
the GatorCam4 Controller will organize all your recordings (videos or
photos) and observations in Jobs structures. This information will also be
used to generate the final detailed report (if required) by using FlexiSight
manager. Consult the operational manual for more details.
To start a new job:
Go to the Job browser: from the main Setup Menu, select "Jobs" and
press OK.
Press NEW (F1) and enter Client, Site and Survey details. Press START to
start the new job.
To resume or review an existing job:
Go to the Job browser: from the main Setup Menu, select "Jobs" and
press OK.
Use the
or
keys to select the Job you wish to resume or review and
press OK.
Press START (F1) to resume the job,
or:
use the
and
keys to select Job details or media (photos or videos),
press OK to review, edit or preview.
Recordings
NOTE: Do not remove or install the removable storage device when
the system is powered and do not switch off the unit while recording.
Failure to comply may damage the removable storage device and /or
recordings.
Formatting the removable storage device will delete all the files.
If you are using a USB flash drive device this will automatically be used to
store all your data (videos, photos and observations) even in the presence
of a compatible CF card.
Video recording
Press the
key to start recording.
Enter job details if required:
• Review Client Name, Site Address and Survey Start and Finish
Survey references by pressing the
and then press OK again to accept the changes.
• On the keypad, press the
inspection.
Press the
key to pause a recording, press the
recording.
Press the
key to finish recording.
Press Fn and
or
to pan a zoomed video image.
Press
or
to zoom in or out.
Press the rotate keys
or
to rotate the video image.
To restore an altered image, simultaneously press both video effects keys
for example
and
.
and
keys. Press OK to Edit
key again to start recording the
key or
to resume
11
Publicité
