Child Anti-Tamper, Keypad Lock/Unlock; Day And Daily Programme Integrated, Energy Savings; Automatic Programming With Self-Learning Process; Day And Daily Programme - RADSON PTC BLOWER 950W Notice D'utilisation

EN
2- Press simultaneously and
To exit resetting the energy meter, press any button, the device is
automatically in the previous active mode.
CHILD ANTI-TAMPER,
KEYPAD LOCK/UNLOCK
Keypad lock
To lock the keypad, press the
and buttons and hold them
down for 10 seconds. The padlock
symbol appears on the display,
the keypad is locked.
Keypad unlock
To unlock the keypad, press the
for 10 seconds again. The padlock symbol
keypad is unlocked.
Important: when the keypad is
locked, only the button (switch) is
active.
If the device is on Standby mode when the
keypad is locked, you have to unlock it for the
next heating on to access the setup.

7 DAY AND DAILY PROGRAMME

INTEGRATED, ENERGY SAVINGS
AUTOMATIC PROGRAMMING WITH SELF-LEARNING
PROCESS
This feature is available on products equipped with occupancy detector.
Overview
Auto-programming (Auto): After an initial learning period of one week,
the device will analyze occupancy cycles to determine and implement
a weekly programme adapted to your lifecycle alternating periods in
comfort and periods in eco, the goal being to deliver the most efficient
yet comfortable and user focused heating cycle. The products algorithm
will perpetually learn and adapt to changes in your occupancy patterns,
adapting week after week to optimize the heating programme to any
changes in your evolving occupancy patterns.
Operating
Upon the first activation of your de-
vice, the mode "auto-programme" is
activated by default,
in mode Auto. To deactivate and
change the programme, see choice
and affectation of programmes page
8.
The first week of operation is a lear-
ning week during which the device
memorizes your habits and elabo-
rates a program for the week.
It therefore defines a programme
built up of periods of Comfort and
Eco, independently for each day of
the week.
During this learning week, the device will provisionally function in per-
manent "Comfort" mode.
Important:
To ensure the auto-programming is optimized, please en-
sure the presence detection sensor is not interrupted by an external
source, see important information concerning the presence detection
M16MI328 A04_02/18 R
for more than 5 seconds.
3
and buttons hold them down
disappears from the display,
3
Example of display
in Comfort period
3
Example of display
in Eco period
system on page 10.
Application of the intelligent program
One week after switching on, the device will apply the new program
for the next 7 days. Then week after week the device will continue to
optimize the intelligent program "Auto", adjusting the Comfort and Eco
periods to fit closely to your lifestyle.
When the product is in Frost protection mode or in standby mode for
more than 24 hours, learning and optimization of the intelligent pro-
gram stops: the device stores the previously recorded program from the
last week before switching to the Frost protection or standby mode.
- Example 1: If the product is installed in mid-season or if its installa-
tion is anticipated on the construction site, it can be switched on in
standby mode. When you select the Auto mode, the learning week
will start automatically. The device will be in permanent comfort and
will memorize your habits to apply the adapted program the following
week.
- Example 2: You select frost protection mode before going on holiday.
Upon your return, when you return to Auto mode, the unit will auto-
matically apply the previously stored intelligent program from the last
week before you left.
In the case of control by pilot wire coming from an energy manager for
example, the pilot wire will take precedence over the AUTO program
which results from the Self-learning algorythm.
7 DAY AND DAILY PROGRAMME
In this mode, you have the option of programming your device, by
setting one of the five programmes on offer for each day of the week.
Access to the programming mode
From Auto, Comfort, Eco or Frost protection mode, press
seconds to enter into the programming mode.
Schematic sequence of programming settings:
Setting time Setting day
Setting day and time
In this mode, you can set day and time to program your device in line
with your needs.
1- From Auto, Comfort, Eco or Frost protection mode, press
seconds.
The cursor moves to the setting day and time mode.
1
2- Select using or . The two hour figures will flash.
The hours will scroll quickly, if you press the
them.
Save by pressing .
1
Programmes
choice
5 sec.
or
1 2
or 5
for 5
and hold
6