Publicité
Les langues disponibles
Les langues disponibles
16
• DO NOT PLACE THE APPLIANCE IN WATER OR ANY LIqUID; NOR HANDLE/ USE IT WITH WET OR
MOIST HANDS.
•
DO NOT USE THE APPLIANCE NEAR WATER CONTAINED IN BATHTUBS, SINKS OR IN OTHER
CONTAINERS.
• DO NOT PLACE OR STORE THE APPLIANCE WHERE IT CAN FALL OR BE PULLED INTO A TUB OR
SINK.
• DO NOT REACH FOR THE APPLIANCE THAT HAS FALLEN INTO WATER. UNPLUG IT IMMEDIATELY.
InseRtInG anD RemovInG the comBs
Notes:
•
Make sure that the appliance is turned off when attaching or removing the combs.
•
The set includes four combs, each of them having different cutting lengths- 3, 6, 9 and
12 mm.
1.
Choose the desired comb.
2.
Slide the upper part of the comb onto the teeth of the cutter and then push lower part
EN
of the comb on the appliance so that the projection at the bottom of the comb locks
on the cutter (you will hear a click). Remove the comb from the blade by pushing it
upwards.
3.
Remove the comb by pushing the projection of the comb upwards.
tIps BefoRe tRImmInG
• prior to trimming, make sure hair is dry and clean.
• trim small amount of hair at a time.
• for the first use or when the user is not acquainted with the appliance, it is
recommended not to trim to a short haircut. to achieve longer haircut, use a comb
with higher markings (9, 12 mm).
• hair length after trimming depends on the comb used. there are markings on each
of the combs: 3 mm, 6 mm, 9 mm and 12 mm. each marking corresponds to the hair
length achieved after trimming.
Owner's manual
ImpoRtant!
Owner's manual
opeRatIon
1.
Connect the appliance to the power supply socket.
2.
Push the on/off switch upwards to turn on the appliance.
3.
Push the taper lever up or down to choose desired setting.
4.
Start cutting your hair:
• To achieve best results it is recommended to stat trimming from the back and
bottom of the head and moving the hair clipper upwards towards the top of the
head.
• When cutting hair with a comb attached, make sure the cutter stays close to the
skin.
• Use the appliance without comb attached for more precise trim (for example on
the temples).
• The appliance has a sharp cutter. Therefore do not press the hair clipper too hard on
the skin to avoid injuries.
• Use the included comb and scissors to further style your hair. Hold the hair with the
comb and cut over the comb with the hair clipper or scissors.
5.
After trimming, turn off the appliance by pushing the on/off switch downwards.
6.
Disconnect the appliance from power supply socket.
7.
If the appliance was used with the comb attached, remove and clean the comb and
the whole appliance according to the instructions included in "Cleaning" section.
* When the lever is set to the highest position, the stationary and moving blades are close
to each other, resulting in a short haircut. Set the lever to the lowest position to increase the
distance between the two blades and as a result achieve longer haircut.
When hair jams in between the moving and stationary blade, push the lever up and down a
few times until hair are released.
cLeanInG
General:
•
Do not immerse the appliance in water.
•
Do not clean the cutter under running water. Clean it only with the included brush.
•
Do not use any abrasives or chemical agents to clean this product.
•
Clean only the casing with a soft and slightly damp cloth.
•
Clean the appliance after each use. Regular cleaning guarantees better shaving
performance.
1.
Make sure the appliance is turned off and disconnected from power mains.
2.
Use the included brush to clean the cutter.
3.
Clean the combs using the brush or rinse them under running water. Make sure to
wipe them dry before refitting.
17
EN
Publicité
