Lovato BIG EXOL AR2 Mode D'emploi page 21

Dear Customer,
Thank you for choosing a product by Lovato. We are confident that we will reward the trust you have placed in us, thanks to a product that is the result of on-going research and careful,
quality-oriented manufacturing.
All of our products are manufactured using top-grade materials and components ensuring long-lasting quality and reliability.
In addition to the product's features and specifications, this document contains instructions addressed to the installer and service technicians, as well as to the end user.
Please note that after installation you should contact our local Customer Service team, who will commission the equipment and validate and confirm the relevant warranty. For your nearest
Customer Service Centre, please call us on (0039) 045 6182012.
For perfect set-up and conscientious periodic maintenance we recommend that you contact one of our Authorized Customer Service Centres at least once a year. Our Service team will not
only carry out a thorough overhaul of the thermal module, but will also perform preventative maintenance in order to prevent problems or unwanted deactivations.
We thank you again for choosing one of our products and we will be more than happy to provide you with any further information and support you may require for the proper operation of
this equipment.
Please read this manual carefully before performing any work on this equipment.
As a part of our policy of continuous product improvement in order to keep up with innovations in technology and to meet specific manufacturing,
installation or positioning requirements, we reserve the right to make modifications to this product without prior notice. Therefore,
although the product delivered may slightly differ from the illustrations shown in this manual, its safety is guaranteed and the instructions
affixed on it are guaranteed to be correct.
This user manual is an integral part of the product. It must be kept in good condition and must be saved for future reference during the
entire service life of this equipment.
Furthermore, it should always be available near the equipment for quick reference and it must accompany it if it is sold or transferred to a
new owner, or if you move and leave the equipment behind, in order to enable the new owner or technician to use it for reference.
Preliminary inspections
Before anything else, remove the packaging and check that the equipment is in perfect condition. If you find a defect or damage, do not
install it or attempt to fix it yourself and instead contact your dealer.
Dispose of the packaging materials in compliance with applicable regulations on disposal.
GENERAL DANGER
Installation
Before performing any work on this unit, the power supply must be disconnected from the mains.
Installation must be performed in compliance with all applicable local laws and regulations.
The liability of the manufacturer is limited to the supply of the product. Its installation must be performed by qualified personnel working
for a company that system. Installation must be carried out in accordance with best practice and the instructions herein and to the highest
professional standards.
LOVATO S.p.A. disclaims any and all liability for any unauthorized modifications or alterations made to the product or if non-genuine spare
parts are used.
Electrical connection
The controller and the entire system may only be installed and connected by qualified personnel in compliance with all applicable laws
and regulations.
Connect the power supply cable of the controller to a two-pole switch equipped with fuses (power supply 230Vac 50Hz). Ensure proper
connection to the grounding system.
Danger
The controller must be connected to the mains with a residual current circuit-breaker fitted upstream, according to applicable regulations.
Proper operation of the controller is guaranteed
only if it is used in conjunction with the motor for which it was designed. Improper use of this unit will relieve the manufacturer of all liability.
Hydraulic connection
After transporting the KIT, or after handling it, tighten all tube union nuts.
Take extreme care when connecting the KIT to the hydraulic system. Avoid bending the copper tubing. To counteract the tightening force
exerted on the tubing connecting the KIT and the hydraulic system, use a spanner or similar tool on the KIT end.
Please follow these vital recommendations when using the equipment:
• Do not touch hot surfaces, such as water inlet and outlet ducts. Hot parts may cause severe burns.
• Do not spray the unit with water or other liquids.
• Do not place any items on the top of the unit.
• Do not expose the unit to steam from cooking equipments.
• Do not allow children or inexperienced people to use this equipment.
• Do not touch this equipment with wet or damp parts of the body and/or with bare feet..
• Do not pull electric wires
• Beware of wearing gauntlets and accident-prevention shoes before handling the product
!
Installation, connection and testing may only be performed by qualified personnel working in
accordance
DANGER !
22004022 - 06.13
2. General instructions for end user
Assembling instructions and maintenance
LOVATO S.p.A.
21