Safety - PLYMOVENT DRAFTMAX ECO Manuel Opérateur

A
J
I
H
G
F
Fig. 2.1: Main components
3

SAFETY

General
The manufacturer does not accept any liability for damage to
the product or personal injury caused by ignoring of the safety
instructions in this manual, or by negligence during installation,
use, maintenance, and repair of the product mentioned on the
cover of this document and any corresponding accessories.
Specific working conditions or used accessories may require
additional safety instructions. Immediately contact your
supplier if you detect a potential danger when using the product.
The user of the product is always fully responsible for
observing the local safety instructions and
regulations.
Observe all applicable safety instructions and
regulations.
User manual
• Everyone working on or with the product, must be familiar
with the contents of this manual and must strictly observe
the instructions therein. The management should instruct
the personnel in accordance with the manual and observe all
instructions and directions given.
• Never change the order of the steps to perform.
• Always keep the manual with the product.
Pictograms and instructions on the product (if
present)
• The pictograms, warning and instructions attached to the
product are part of the safety features. They must not be
covered or removed and must be present and legible during
the entire life of the product.
• Immediately replace or repair damaged or illegible
pictograms, warnings and instructions.
Users
• The use of this product is exclusively reserved to well
authorised, trained and qualified users. Temporary
personnel and personnel in training can only use the product
under supervision and responsibility of skilled engineers.
0507061410 DraftMax Eco
Intended use
The product has been designed as a workbench for welding and
grinding and cutting purposes, to be connected to an external
B
extraction/filtration facility. Using the product for other
purposes is considered contrary to its intended use. The
manufacturer accepts no liability for any damage or injury
C
resulting from such use. The product has been built in
accordance with state-of-the-art standards and recognised
safety regulations. Only use this product when in technically
perfect condition in accordance with its intended use and the
instructions explained in the user manual.
Technical specifications
The specifications given in this manual must not be altered.
Modifications
Modification of (parts of) the product is not allowed.
Use
WARNING
Fire hazard! Never use the product for:
D
- filtering flammable, glowing or burning particles or
solids or liquids
- filtering of aggressive fumes (such as hydrochloric
E
acid) or sharp particles
- sucking cigarettes, cigars, oiled tissues, and other
burning particles, objects, and acids
WARNING
Never use the product for:
- arc-air gouging
- oil mist
- paint mist
- heavy oil mist in welding fume
- extraction of hot gases (more than 45°C/113°F
continuously)
- grinding aluminium and magnesium
- flame spraying
- extraction of cement, saw dust, wood dust etc.
- explosive environments or explosive substances/
gases
• Inspect the product and check it for damage. Verify the
functioning of the safety features.
• Check the working environment. Do not allow unauthorised
persons to enter the working environment.
• Protect the product against water and humidity.
• Use common sense. Stay alert and keep your attention to
your work. Do not use the product when you are under the
influence of drugs, alcohol or medicine.
• Make sure the room is always sufficiently ventilated; this
applies especially to confined spaces.
• Never install the product in front of entrances and exits
which must be used for emerency services.
• Make sure that the workshop, in the vicinity of the product,
contains sufficient approved fire extinguishers.
Service, maintenance and repairs
• Observe the maintenance intervals given in this manual.
Overdue maintenance can lead to high costs for repair and
revisions and can render the guarantee null and void.
• Always use tools, materials, lubricants and service
techniques which have been approved by the manufacturer.
Never use worn tools and do not leave any tools in or on the
product.
• Safety features which have been removed for service,
maintenance or repairs, must be put back immediately after
finishing these jobs and it must be checked that they still
function properly.
1. "Intended use" as explained in EN-ISO 12100 is the use for which the
technical product is suited as specified by the manufacturer, inclusive
of his directions in the sales brochure. In case of doubt it is the use
which can be deducted from the construction, the model and the
function of the technical product which is considered normal use.
Operating the machine within the limits of its intended use also
involves observing the instructions in the user manual.
1
EN - 3