Direto Xr For Ø12 L=142 Mm Chainstays; 18_Power Supply; 19_Removing The Bicycle; 20_Installation Instructions For Free-Hub Body - eLine DIRETO XR Mode D'emploi

triangle) (Pic. 18).
NOTE: the knurled side of the triangle adapter (Ref. C) must
be facing the bicycle dropout.
- Securely fix the bicycle to DIRETO XR and firmly close the
quick release (Ref. ). The resulting pressure should keep
the bicycle dropouts locked to the DIRETO XR.
17_INSTALLING THE DIRETO XR ON
BICYCLES WITH Ø12 L=142 MM
CHAINSTAYS
1) Insert the left adapter (Ref. G) and screw the rigth
adapter (Ref F) for 142mm carriages (Fig. 16);
2) Loosen the rear brake of the bicycle and place the chain
on the smallest sprocket of the rear wheel and the front
chainring. Remove the thru-axle from the rear wheel.
3) Position the bicycle's rear dropouts on the axle of the
sprocket cassette of the DIRETO XR.
4) Insert the thru-axle on the DIRETO XR sprocket cassette
shaft.
5) Make sure the bicycle is safely positioned on the DIRETO
XR and lock the thru-axle with a strong push. The pressure
should make the bike dropouts remain locked onto the
structure of the DIRETO XR.
6) Make sure the bike is stable by pushing and pulling the
top tube of the frame and the saddle. Should the bike still
be moving a little on the DIRETO XR, use more force to lock
the thru-axle.
7) If you wish for more bicycle stability it's advisable to
use the provided Riser block (Ref I) to be placed under the
front wheel.
- Start pedalling. Ride very slowly at first and increase your
speed gradually until you become familiar with the features
of DIRETO XR.

18_POWER SUPPLY

- DIRETO XR has an electronic motherboard that is powered
via a standard power supply adapter (included).
- Connect the power supply to the grid and the jack to the
proper connector on the back of the DIRETO XR. A small
vibration indicates that the system is booting up to its initial
position. This operation might last up to 15 seconds.
Hang the power supply cable on the dedicated hanger (Pics
21 and 22).
The DIRETO XR compliance with EU laws (see "Declaration
of conformity", page 112) may be voided if a charger
different from the original is used.

19_REMOVING THE BICYCLE

- Shift the bicycle chain on the smallest cassette sprocket
of DIRETO XR and of the smallest front chainring of the
bicycle.
- Open up the quick release (or remove the thru-axle) and
remove the bicycle from the DIRETO XR.
- To avoid clutter or for transportation: loosen the knobs
(Pic. 23) and fold the side legs (Pic. 24 - 25).
20_INSTALLATION INSTRUCTIONS FOR FREE-
HUB BODY COMPATIBLE WITH CAMPAGNOLO
9/10/11/12 SPEED SPROCKET CASSETTE,
FREE-HUB BODY COMPATIBLE WITH XD/
XDR SRAM 12 SPEED, FREE-HUB BODY
COMPATIBLE WITH MICRO SPLINE SHIMANO
12 SPEED
- Replace the free-hub body originally present on the
DIRETO XR with the accessory compatible with 9/10/11/12
speed CAMPAGNOLO sprocket cassette or XD/XDR
compatible free-hub body (for 12 speed SRAM sprocket
cassette) or Micro Spline compatible free-hub body (for
SHIMANO 12-speed sprocket cassette) following the
following steps:
1) Remove the cassette pre-assembled on the hometrainer
(Pic. 22 )
2) Unscrew the fastening sleeve (Pic. 23).
3) Remove the freehub body from the DIRETO XR shaft
(Pic. 24).
4) Fully insert the body compatible with CAMPAGNOLO or
XD/XDR or Micro Spline sprocket cassette. (Pic. 25 and
26).
5) Tighten the fastening sleeve with a 17 straddle wrench
with a 5Nm (44in-lbs) tightening torque. Use the medium
resistance threadlocker suitable for oily surfaces to lock the
sleeve on the shaft.
Only for CAMPAGNOLO compatible body:
- 2 spacers (Ref. B) are usually needed for the 9 speed
cassette (Pic. 6), 1 spacer for the 10 speed cassette (Pic.
7) and no spacer is required for the 11 speed cassette.
Depending on the cassette brand you are using there might
be some differences with the aforementioned general data.
ATTENTION!
Strictly follow the instructions provided by the cassette
manufacturer with regard to specific installation techniques,
the need for additional spacers and torque specifications.
NOTE: Please contact your dealer if you have questions
about installation or if you cannot install the cassette. The
warranty does not cover any damage to the bicycle and/or
DIRETO XR in the event of incorrect installation.

21_MAINTENANCE

DIRETO XR does not require any specific scheduled
EN
35