Publicité
Les langues disponibles
Les langues disponibles
Connect the machine to a properly
earthed mains supply. The socket
outlet and the extension cable must
have an operative protective
conductor.
Provide for good ventilation at the
working place.
Do not use the machine as a ladder or
step ladder. The machine can tip over
and become damaged. Danger of
injury.
Only use the socket outlet on the
machine for purposes specifi ed in the
instructions.
RISKS
Electrical components
DANGER!
The upper section of the machine
contains live components.
Contact with live components leads to
serious or even fatal injuries.
Never spray water on to the upper
section of the machine.
DANGER!
Electric shock due to faulty mains
connecting lead.
Touching a faulty mains connecting
lead can result in serious or even fatal
injuries.
• Do not damage the mains power lead
(e.g. by driving over it, pulling or
crushing it).
• Regularly check whether the power
cord is damaged or shows signs of
ageing.
• If the electric cable is damaged, it
must be replaced by an authorized
Milwaukee distributor or similar
24
ENGLISH
qualifi ed person in order to avoid a
hazard.
• In no circumstances should the power
supply cord be wrapped around
fi ngers or any part of the operators
person.
• Hazardous dust
WARNING!
Hazardous materials.
Vacuuming up hazardous materials
can lead to serious or even fatal
injuries.
The following materials must not be
picked up by the machine:
• hot materials (burning cigarettes, hot
ash, etc.)
• fl ammable, explosive, aggressive
liquids (e.g. petrol, solvents, acids,
alkalis, etc.)
• fl ammable, explosive dust (e.g.
magnesium or aluminium dust, etc.)
Spare parts and accessories
CAUTION!
Spare parts and accessories.
The use of non-genuine spare parts, brushes and accessories can
impair the safety and or function of the appliance.
Only use original spare parts and accessories from Milwaukee.
Spare parts that can aff ect health and safety of the operator and or
function of the appliance, are specifi ed below:
Description
Order No.
Flat fi lter PTFE, 1 pcs.
4932 4596 87
Fleece fi lter bag, 5 pcs.
4932 459689
Disposal bag, 5 pcs.
4932 4596 90
Motor cooling air fi lter PET, 1 pcs.
4932 4596 88
In explosive or infl ammable atmosphere
CAUTION!
This machine is not suitable for use in explosive or infl ammable
atmospheres or where such atmospheres are likely to be produced
by the presence of volatile liquid or infl ammable gas or vapour.
CONTROL / OPERATION
CAUTION!
Damage due to unsuitable mains voltage.
The appliance can be damaged as a result of being connected to
an unsuitable mains voltage.
• Ensure that the voltage shown on the rating plate corresponds to
the voltage of the local mains power supply.
Starting and operating of the machine
Check that the electrical switch is switched off (in position 0).
Check that suitable fi lters are installed in the machine.Then
connect the suction hose into the suction inlet at the machine by
pushing the hose forward until it fi ts fi rmly in place at the inlet.
Then connect the tubes with the hose handle, twist the tubes in
order to ensure that they are properly fi tted. Attach suitable nozzle
to the tube. Choose nozzle depending on what type of material that
is to be picked-up. If used for dust extraction in connection
with dust producing tool then connect end of suction hose with
appropriate adapter. Connect the plug into a proper electrical
outlet. Put the electrical switch into position I in order to start the
motor.
Turn I: Activate the machine
Turn
: Stop the machine.
Permanent power on socket.Turn
Activate Auto-On/Off operation.
Turn I+
Off : Activate the machine with
deactivated auto-matic fi lter cleaning function
Turn
+
Off : Activate Auto-On/Off
operation with deactivated automatic fi lter
cleaning function. Speed control operation
on separate turning knob
The hose diameter and the setting for suction hose diameter must
be the same.
ø21
ø21
ø27
ø27
ø32
ø32
ø36
ø36
ø38
ø38
Auto-On/Off socket outlet for power tools
CAUTION!
Appliance socket.
The appliance socket is designed for electrical auxiliary equipment;
see technical data for reference.
• Prior to plugging in an appliance, always switch off the machine
and the appliance that is to be connected.
• Read the operating instructions to the appliance to be connected
and observe the safety notes contained in these.
An appliance socket with earthing contact is integrated in the
machine. An external power tool can be connected there. The
socket features permanent power on, when the electrical switch is
in position
, i.e. the machine can be used as an extension
cord.
In position
the machine can be switched on and off by the
power tool connected. Dirt is picked up from the source of dust
immediately. To comply with regulations, only approved dust
producing tools should be connected.
The maximum power consumption of the connected electrical
appliance is stated in section "Specifi cations".
Before turning the switch to position
ensure that the tool
connected to the appliance socket is switched off .
Auto-Clear
The "IC" machine is equipped with an automatic fi lter cleaning
system, Auto-Clear. A frequent cleaning cycle will automatically run
during operation to ensure that suction performance is always at its
best.
If suction performance decreases or in extensive dust applications
a manually fi lter cleaning operation is recommended:
• Switch off the machine
• Close the nozzles or suction hose opening with the palm of your
hand.
• Turn the switch to position „I" and let the machine operate at full
speed for approx. 10 seconds with the suction hose opening
closed.
If suction power is still reduced take out the fi lter and clean
mechanically or replace fi lter.
For certain applications, like wet pick up, it is recommended to turn
off the automatic fi lter cleaning system. For details see chapter
Starting and operating of the machine.
:
Flow rate warning
CAUTION!
Check that all the fi lters are present and properly fi tted.
The machine is equipped with a system to monitor air velocity and
Dust Class H fi lter condition
*)
. Before picking up dust with
occupational exposure limit values, check the volume fl ow monitor.
When the motor is running, hold the suction hose shut to reduce
the volume fl ow. The LED indicator on front panel will light after
approx. 1 second. The acoustic warning sounds after some additional
seconds.
Set the diameter setting to the actual hose size.
When LED indicator lights, air velocity is below 20 m/s.
•
check if container or fi lter bag is full.
• check if air fl ow is reduced in suction hose, tube/nozzle, fi lter.
Antistatic connection
CAUTION
The machine is equipped with an antistatic system to discharge
any static electricity that may develop during dust pick-up.
The antistatic system is placed in front part of the motor top and
creates an earth ground connection to the inlet fi tting of the
container. For proper function the use of an electrical conductive or
antistatic suction hose is recommended. When inserting the
optional disposal bag make sure the antistatic connection is kept.
Cooling air fi lter
To protect the electronics and motor, the machine is equipped with
a cooling air diff usor. Clean the cooling air diff usor regularly.
For areas with a high concentration of fi ne dust in the surrounding
air it is recommended to equip the machine with an optional
cooling air fi lter cartridge to prevent dust from settling inside the air
channels and motor. Contact your local sales representative.
CAUTION!
If cooling air fi lter is clogged by dust the overload protection switch
in the motor can be activated. In such case switch off the machine,
clean cooling air fi lter and allow machine to cool for approx. 5
minutes.
Wet pick-up
CAUTION!
The machine is equipped with a water level limit system which
shuts off the machine when the maximum liquid level is reached.
When this occurs, switch off the machine. Disconnect the machine
from the socket and empty the container. Never pick up liquids
without the water level limit system and fi lter in place.
Picking up liquids.
ENGLISH
25
Publicité
