Inglis W11035214A Guide D'utilisation page 15

Troubleshooting
First try the solutions suggested here or visit our website at inglis.ca for assistance and to possibly avoid a service call.
If you experience
Washer not performing as expected (cont.)
Washer won't run
or ll, washer stops
working, or wash light
remains on (indicating
that the washer was
unable to ll
appropriately) (cont.)
Washer not draining/
spinning, loads are still
wet, or nal spin light
remains on (indicating
that the washer was
unable to pump out
water within 10 minutes)
Dry spots on load
after cycle
Incorrect or wrong
wash or rinse
temperatures
Load not rinsed
Possible Causes
Normal washer operation.
Washer may be tightly packed.
Small items may have been caught
in pump or between basket and tub,
which can slow draining.
Using a cycle with a low spin speed.
The washer may be tightly packed
or unbalanced.
Check plumbing for correct drain
hose installation. Drain hose
extends into standpipe further
than 4.5" (114 mm).
Too much detergent causing suds
to slow or stop draining and spinning.
High speed spins extract more
moisture than traditional top-load
washers.
Washer may be tightly packed.
Added extra garments to the load
after the sensing/ ll phase.
Check for proper water supply.
Energy saving controlled
wash temperatures.
Check for proper water supply.
Not using HE detergent or using too
much HE detergent.
Washer not loaded as recommended. The washer is less ef cient at rinsing when load is tightly packed.
Lid must be closed for washer to run.
Washer will pause during certain phases of cycle. Do not
interrupt cycle.
Remove several items, rearrange load evenly in basket, and
add detergent. Close lid and press START/PAUSE/UNLOCK
LID/CANCEL.
Do not add more than one or two additional items after cycle
has started to avoid tightly packing or unbalancing.
Empty pockets and use garment bags for small items.
Cycles with lower spin speeds remove less water than cycles
with high spin speeds. Use the recommended cycle/spin speed
for your garment. To remove extra water in the load, select
Drain/Spin. Load may need to be rearranged to allow even
distribution of the load in the basket.
Tightly packed or unbalanced loads may not allow the washer
to spin correctly, leaving the load wetter than normal. Evenly
arrange the wet load for balanced spinning. Select the Drain/
Spin cycle to remove excess water. See "Using Your Washer"
for loading recommendations.
Check drain hose for proper installation. Use drain hose form
and securely attach to drain pipe or tub. Do not tape over drain
opening. Lower drain hose if the end is higher than 96" (2.4 m)
above the oor. Remove any clogs from drain hose.
Always measure and follow detergent directions for your load.
To remove extra suds, select Rinse/Spin. Do not add detergent.
The high spin speeds combined with air ow during the nal
spin can cause items near the top of the load to develop dry
spots during the nal spin. This is normal.
Use Bulky/Sheets cycle for higher water ll, or set Water Level
knob to Deep Water Wash setting. See "Cycle Guide" to match
your load with the best cycle.
Add only one or two additional garments after washer
has started.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached to both washer and faucet
and have both hot and cold water owing to inlet valve.
Check that inlet valve screens are not clogged.
Remove any kinks in hoses.
This washer uses cooler wash and rinse water temperatures than
your previous washer. This includes cooler hot and warm washes.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached and have water owing to the
inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
The suds from too much detergent can keep washer from
operating correctly. Always measure detergent and follow
detergent directions based on load size and soil level.
Load garments in loose heaps evenly around the basket wall.
Load with dry items only.
Solution
15