Publicité
EN
INTRODUCTION
Please read it carefully before installing the appliance, before using it and before routine or
extraordinary maintenance work.
The notices preceded by this symbol provide important information, the non-compliance with such
instructions voids the manufacturer's guarantee.
OPERATIONS THAT, IF NOT CARRIED OUT CORRECTLY, CAN BE RISKY, ARE INDICATED WITH THE FOLLOWING SYMBOLS:
The INSTALLATION, USE AND MAINTENANCE handbook is for installers, users and maintenance engineers
The Company is not liable for injury to people or animals or damage to things in the case of applications that exceed the
limits specifi ed on the enclosed technical data sheet or by a use diff erent from what the appliance has been designed.
Warning! Observe all the instructions, improper installation, use and maintenance can result in serious injury.
GENERAL
Deterrent bollard crash-tested and certifi ed by accredited third-party Laboratory according to IWA14-1:2013 V/7200[N3C]/80/90,
equivalent to PAS68:2010 7500/80/N3 and ASTM2656:2007 M50.
GENERAL SAFETY
• Keep hold of instructions so that you can attach them to the technical fi le and keep them handy for future reference.
• Installation must be carried out by qualifi ed personnel (professional installer, according to EN 12635), in compliance with Good
Practice and current code.
• Make sure the stated temperature range is compatible with the site in which the automated system is due to be installed.
• Install any fi xed controls in a position where they will not cause a hazard, away from moving parts. More specifi cally, hold-to-run
controls must be positioned within direct sight of the part being controlled and, unless they are key operated, must be installed
at a height of at least 1.5 m and in a place where they cannot be reached by the public.
• During installation, the power cable must be stripped to allow the earth wire to be connected to the relevant terminal, while
leaving the live wires as short as possible. The earth wire must be the last to be pulled taut in the event the cable's fastening
device comes loose.
• Scrap packing materials (plastic, cardboard, polystyrene etc) according to the provisions set out by current standards. Keep nylon
or polystyrene bags out of children's reach.
• Disconnect the electrical power supply before carrying out any work on the installation. Also disconnect any UPS, if fi tted.
• Fit an omnipolar or magnetothermal switch on the mains power supply, having a contact opening distance equal to or greater
than 3,5 mm.
• Check that a diff erential switch with a 0,03A threshold is fi tted just before the power supply mains.
• The outputs are not of type SELV (separated extra-low voltage), therefore it must not be possible to reach them.
• Fit all the safety devices (photocells, electric edges etc.) which are needed to protect the area from any danger caused by squashing,
conveying and shearing, according to and in compliance with the applicable directives and technical standards.
• The Company decline s all responsibility with respect to the automation safety and correct operation when other manufacturer's
components are used.
• Only use original parts for any maintenance or repair operation.
• Do not modify the automation components, unless explicitly authorised by the Company.
• Instruct the product user about the control systems provided and the manual opening operation in case of emergency.
• Do not allow persons or children to remain in the automation operation area.
• Keep radio control or other control devices out of children's reach, in order to avoid unintentional automation activation.
• Do not allow children to play with the equipment.
• The equipment may be used by children aged over 8 years old and by people with reduced physical, sensory or mental capabi-
lities, or without experience or the necessary knowledge, provided they are supervised or after they have received instructions
relating to the safe use of the equipment and have understood the dangers inherent in it.
• Cleaning and maintenance meant to be performed by the user must not be performed by unsupervised children.
• Anything which is not expressly provided for in the present instructions, is not allowed.
TECHNICAL SPECIFICATIONS
Power............................................230 Vac ± 10%; 50÷60 Hz
Nominal power consumption...................................1500 W
Maximum current consumption....................................10 A
Maximum working frequency..........................2 000 / 24h
Protection level......................................................................IP67
Control unit..........................PERSEO CBE (max 2 bollards)
Operating temperature............................-40 *** to +60 °C
*** With integrated heater active
ELECTROCUTION
CRUSHING
Rise time (standard version)....................................~ 6.3 s**
Rise time (version with EFO)....................................~ 1.5 s**
Lowering time
(factory adjusted, on-fi eld adjustable)................~ 4.0 s**
Net weight...........................................................................690 kg
Gross weight.......................................................................756 kg
** At 25 °C ambient temperature
- 4 -
Publicité
