Publicité
EN
GENERAL SAFETY
• Any use other than that expressly permitted is prohibited (see GENERAL).
• Keep adults, children and property out of range of the automated system, especially while it is operating.
• For safety reasons and to comply with current standards, we recommend using the control unit.
• To install follow the instructions given in the enclosed "GENERAL INSTRUCTIONS FOR SAFETY" sheet.
• All electrical connections must be done in compliance with current laws.
• For safety reasons and to comply with current standards, we recommend using the control unit.
• The construction components of this product must comply with the following European Directives: 2006/42/EEC, 2014/35/UE,
2014/30/UE, 2014/53/UE, and subsequent amendments. As for all non-EEC countries, the above-mentioned standards as well
as the current national standards should be respected in order to achieve a good safety level.
• The Company declines all responsibility for any consequences resulting from failure to observe Good Technical Practice when
installing the device described in the present manual.
• Do not install the product in potentially explosive atmosphere or wherever there is a fi re risk.
• Disconnect the electrical supply before carrying out any work on the installation. Also disconnect any buff er batteries, if fi tted.
• Fit an omnipolar or magnetothermal switch on the mains power supply, having a contact opening distance equal to or greater
than 3,5 mm. Also fi t an adequate cut-out device for the buff er batteries.
• Check that a diff erential switch with a 0.03A threshold is fi tted just before the power supply mains.
• Check that earthing is carried out correctly.
• Installation must be carried out using the safety devices and controls prescribed by the EN 12978 Standard.
• Fit all the safety devices (photocells, electric edges etc.) which are needed to protect the area from any danger caused by
squashing, conveying.
• Position at least one luminous signal indication device (blinker) where it can be easily seen, and fi x a Warning sign next to the
structure.
• Only use original parts for any maintenance or repair operation. The Company declines all responsibility with respect to the
automation safety and correct operation when other producers' components are used.
• Do not modify the automation components, unless explicitly authorised by the Company.
• Scrap packing materials (plastic, cardboard, polystyrene etc) according to the provisions set out by current standards. Keep nylon
or polystyrene bags out of children's reach.
• Anything which is not expressly provided for in the present instructions, is not allowed.
• Instruct the product user about the control systems provided and the manual opening operation in case of emergency.
• Analyse the risks and take all the appropriate measures to eliminate them, as prescribed by the EEC machine directive 2006/42,
installing the safety devices.
• Do not allow persons or children to remain within the automation operation area.
• Keep radio control or other control devices out of children's reach, in order to avoid unintentional automation activation.
• Cleaning and maintenance meant to be performed by the user must not be performed by unsupervised children.
WARNINGS
Correct controller operation is only ensured when the data contained in the present manual are observed. The Company is
not to be held responsible for any damage resulting from failure to observe the installation standards and the instructions
contained in the present manual.
The descriptions and illustrations contained in the present manual are not binding. The Company reserves the right
to make any alterations deemed appropriate for the technical, manufacturing and commercial improvement of the
product, while leaving the essential product features unchanged, at any time and without undertaking to update the
present publication.
USE
• Consult the control unit's installation and operating manual.
• It is essential to follow the instructions given in the enclosed "GENERAL INSTRUCTIONS FOR SAFETY" sheet.
ROUTINE MAINTENANCE (EVERY 6 MONTHS)
• Maintenance must be carried out by qualifi ed personnel only.
• Always disconnect the electricity before attempting any work on the system with a lockable cut-off switch.
• Visually check the overall state of wear and tear of the external parts of the deterrent bollard.
• Make sure the rear-refl ecting fi lm is not worn.
• Make sure the lights work.
• Make sure the control unit and safety devices are in proper working order.
• Check that electrical connections and cabling are intact, making extra sure that insulating sheaths and cable glands are undamaged.
• Record maintenance in the form on the page 25.
- 20 -
Publicité
