EINHELL OPAL Instructions De Montage page 6

Page 30
30/e: Next, hinge blades are attached to two door
profiles (item 10) (refer to the detail drawing). Attach
a hinge blade to each end of the side door profile,
approximately 10 cm from the edge. Make sure that
the hinge blades are inserted in the way shown in the
profile diagram.
Page 31
Note: No pre-assembly is required for the fourth side
door profile.
Page 32
Assembly of the upper door wing
30/h + 30/i: Attach the side door profile with the
striker plate on the right-hand side of the door closing
profile with the hole (item 11). On the left-hand side,
attach the side door profile with the two pre-
assembled hinge blades (refer to step 30/e).
During assembly of the side door profiles, make sure
that the hinges and the striker plate are correctly
positioned (refer to the profile diagram).
Page 34
30/l: Insert the handle (item 5) from the outside
through the hole on the lower door closing profile. On
the inside, push on the locking device (item 6) and
secure it with a washer (item 1) and a self-drilling
screw with tapping screw thread (item 16). Make sure
that after the locking devices are installed they are
positioned at a 90 degree angle (clockwise) in
relation to the handle (see illustration below), as this
is necessary to ensure that the door subsequently
opens and closes smoothly.
Page 35
Assembly of the lower door wing
30/m + 30/n: Attach the side door profile without
bolts on the right-hand side of the door closing profile
(item 9). On the left-hand side, attach the side door
profile with the two pre-assembled hinge blades (refer
to step 30/e). During assembly of the side door
profiles, make sure that the hinges are correctly
positioned (refer to the profile diagram).
Page 37
Figure 30/q (external view): Note the notch on the
lock housing.
30/q: The door latch is attached to the lower door
wing on the side without the hinge. First insert the
latch (item 7) knob-first into the lock housing (item 8).
Align the door latch on the upper door profile so that
the notch on the housing rests against the side
6
ABA_OPAL_Teil2_Titel+GB.pmd 6
profile of the door. Then slide the knob on the latch
up to the second marking so that the holes on the
latch and the housing line up. Attach the door latch
to the door profiles using two self-drilling screws with
tapping screw threads.
Page 38
31
Assembly of the single door
Page 39
Note (Figure 31/c): During assembly of the door
wing stop (art. no. 84.080.42), make sure that the
upper door wing is opened further than the lower.
Page 40
Figure 31/e: External view of the lower part of the
door
31/e: Before you fit the door stay, open the door and
mark on the door profile the position at which the clip
stops against the door. Fit the door stay at this point
(Art. No. 57.013.32).
Page 41
31/f: Now align the striker plates which have already
been pre-assembled on the door hinge. The lower
striker plate is aligned so that the latch can be
pushed into the ear. The upper striker plate should be
level with the plate already assembled on the upper
door wing to allow a padlock (not included with the
greenhouse) to be attached.
31/g: The DT latch mounted on the upper door wing
joins the two halves of the door. Rotate the DT latch
through 90 degrees until it clamps the rabbet profile
on the lower door wing.
Page 42
32
Pre-assembly of the window
Important note: The step below describes the
method for assembling a single window. If you have
purchased a 4-panel greenhouse or a 5-panel
greenhouse, repeat this step for the second
window.
Page 44
Important note: The outside of the plastic web
panels (with UV coating) is marked „Außenseite /
Outside" at the edge, and it is also the side onto
which the protective film has been stuck. Only
remove the protective film from the plastic web panel
you are currently installing.
05.04.2006, 22:37