Air Supply; Lubrication - Napa Professional 6-1129 Guide D'utilisation

AIR SUPPLY

Whip Hose
Do Not Install
Quick Coupling Nipple
Here
Leader
Hose
Tools operate on a wide range of
air pressures. It is recommended
that air pressure measures 90 psig
at the tool with the trigger fully
depressed and no load applied to
the tool. Higher pressure (over 90
psig; 6.2 bar) raises performance
beyond the rated capacity of the
tool, which will shorten tool life
and could cause injury.
Always use clean, dry air. Dust,
corrosive fumes and/or water in
the air line will cause damage to
the tool. Drain the water from air
lines and compressor prior to
running tool. Clean the air inlet
filter screen weekly.
The air inlet used for connecting
air supply has standard 1/4" NPT.

LUBRICATION

Lubricate the air motor daily with
high quality NAPA air tool oil. If
no air line oiler is used, run 1/2 oz.
of oil through the tool. The oil can
be squirted into the tool air inlet
or into the hose at the nearest
OPERATION
This ratchet is rated at 1/4" USS
bolt size. Rat ing must be down
grad ed for spring U bolts, tie bolts,
long cap screws, double depth
nuts, badly rust ed conditions and
spring fas ten ers as they absorb
much of the impact power. When
possible, clamp or wedge the bolt
to prevent springback.
Soak rusted nuts in penetrating
oil and break rust seal before
removing with impact ratchet. If
nut does not start to move in three
to five seconds use a larger size
PLEASE REVIEW ALL WARNING INSTRUCTIONS PRIOR TO OPERATION. SAVE THIS MAN U AL FOR FUTURE REF ER ENCE.
6-1129
Nipple
Quick Coupler Oiler
Line pressure should be increased
to compensate for unusually long
air hoses (over 25 feet). Minimum
hose diameter should be 3/8" I.D.
and fittings should have the same
inside dimensions and be tightly
secured.
Always turn off the air supply,
drain hose of air pressure and
detach tool from air supply before
installing, removing or adjusting
any part or accessory on this tool,
or before performing any
maintenance on this tool.
Ensure an accessible emergency
shut off valve has been installed
in the air supply line and make
others aware of its location.
connection to the air supply, then
run the tool. A rust inhibitive oil is
acceptable for air tools.
WARNING: After an air tool has
been lubricated, oil will discharge
impact ratchet. Do not use impact
ratchet beyond rated capacity as
this will drastically reduce tool life.
The reverse button is used to
change the rotation of the tool.
When the button is turned to the
left, the tool is in a for ward or
right hand ro ta tion. When the
button is turned to the right, the
ro ta tion is reverse or left hand.
NOTE: Actual torque on a fastener
is directly related to joint hardness,
tool speed, condition of socket
Air Supply
Filter
Regulator
Drain Daily
3
S
pecificationS
Drive Size ................................1/4"
Standard Bolt Size ..................1/4"
Max. Free Speed ............. 270 RPM
Working Torque ......... 5-25 ft./lbs.
Max. Torque................... 30 ft./lbs.
Air Inlet .......................... 1/4" NPT
Min. Hose Size ................ 3/8" I.D.
Avg. Air Cons. ............... 3.22 CFM
Recom.
Air Pressure .......90-PSIG (6.2 bar)
Length ...................................7.36"
Weight. ............................ 1.30 lbs.
Sound Power Level ............97 dBA
Forward/Reverse Button
through the exhaust port during
the first few seconds of operation.
The exhaust port must be covered
with a towel before applying air
pressure to prevent serious injury.
and the time the tool is allowed
to impact. Use the simplest
possible tool-to-socket hook up.
Every connection absorbs energy
and reduces power.
NOTE: Always turn off the air
supply, drain hose of air pressure
and detach tool from air supply
before installing, removing or
adjusting any part or accessory
on this tool, or before performing
any maintenance on this tool.
Air Inlet
Rev. 2/23/16