DeWalt DWE575 Traduction De La Notice D'instructions Originale page 52

EN GLI SH
point of the unit bevel is not stationary and the blade
moves out over when the unit is bevelled.
USING THE CORRECT CHANNEL (FIG. 19–21)
The saw base plate consists of two channels. One
channel is for making parallel cuts and the other
channel is for making bevel cuts.
The indicators at the front of the base plate (fig. 19)
indicate which channel is for which application.
When making cuts make sure that the line on the
base plate is in line with the channel on the guide
rail. Figure 20 shows the saw in the parallel cutting
position relative to the guide rail. Figure 21 shows
the saw in the bevel cutting position relative to the
guide rail.
Prior to Operation
• Make sure the guards have been mounted
correctly. The saw blade guard must be in
closed position.
• Make sure the saw blade rotates in the direction
of the arrow on the blade.
• Do not use excessively worn saw blades.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. An
accidental start-up can cause injury.
Proper Hand Position (fi g. 22)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the
main handle (c), with the other hand on the auxiliary
handle (f).
Switching On and Off (fi g. 1)
For safety reasons the trigger switch (a) of your tool
is equipped with a lock-off button (b).
Press the lock-off button to unlock the tool.
50
To run the tool, press the trigger switch (a). As soon
as the trigger switch is released, the lock-off switch
is automatically activated to prevent unintended
starting of the machine.
NOTICE: Do not switch the tool ON or
OFF when the saw blade touches the
workpiece or other materials.
Workpiece Support (fi g. 23–26)
WARNING: To reduce the risk of
serious personal injury, support the
work properly and hold the saw
firmly to prevent loss of control.
Figures 23 and 25 show proper sawing position.
Figures 24 and 26 show an unsafe condition. Hands
should be kept away from cutting area, and power
cord is positioned clear of the cutting area so that it
will not get caught or hung up on the work.
To avoid kickback, ALWAYS support board or panel
NEAR the cut, (fig. 23 and 25). DON'T support
board or panel away from the cut (fig. 24 and 26).
When operating the saw, keep the cord away from
the cutting area and prevent it from becoming hung
up on the work piece.
ALWAYS DISCONNECT SAW BEFORE MAKING
ANY ADJUST MENTS! Place the work with its
"good" side—the one on which appearance is most
important—down. The saw cuts upward, so any
splintering will be on the work face that is up when
you saw it.
Cutting
WARNING: Never attempt to use this
tool by resting it upside down on a
work surface and bringing the material
to the tool. Always securely clamp the
workpiece and bring the tool to the
workpiece, securely holding the tool with
two hands as shown in figure 25.
Place the wider portion of the saw base plate
on that part of the work piece which is solidly
supported, not on the section that will fall off when
the cut is made. As examples, figure 25 illustrates
the RIGHT way to cut off the end of a board. Always
clamp work. Don't try to hold short pieces by hand!
Remember to support cantilevered and overhanging
material. Use caution when sawing material from
below.
Be sure saw is up to full speed before blade contacts
material to be cut. Starting saw with blade against
material to be cut or pushed forward into kerf can
result in kickback. Push the saw forward at a speed
which allows the blade to cut without laboring.
Hardness and toughness can vary even in the same
piece of material, and knotty or damp sections can