Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
EN
WARNING! or CAUTION! or REMEMBER!
Applicable to the given situation (general
warning sign).
ATTENTION! Electric shock warning!
Class II protection device with double
insulation.
ATTENTION! Hot surface, risk of burns!
Only use indoors.
Do not cover the device with any fabrics or
items.
PLEASE NOTE! Drawings in this manual are for
illustration purposes only and in some details may
differ from the actual product.
The original operation manual is written in German.
Other language versions are translations from the
German.
2. USAGE SAFETY
ATTENTION! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in serious injury or even
death.
The terms „device" or „product" are used in the warnings
and instructions to refer to CERAMIC WALL HEATER.
2.1. ELECTRICAL SAFETY
a)
The plug must fit the socket. Do not modify the
plug in any way. Using original plugs and matching
sockets reduces the risk of electric shock.
b)
Avoid touching earthed elements such as pipes,
heaters, boilers and refrigerators. There is an
increased risk of electric shock if the earthed
device is exposed to rain, comes into direct
contact with a wet surface or is operating in
a damp environment. Water getting into the
device increases the risk of damage to the device
and of electric shock.
c)
Do not touch the device with wet or damp hands.
d)
Use the cable only for its designated use. Never
use it to carry the device or to pull the plug out of
a socket. Keep the cable away from heat sources,
oil, sharp edges or moving parts. Damaged or
tangled cables increase the risk of electric shock.
e)
If using the device in a damp environment cannot
be avoided, a residual current device (RCD) should
be applied. The use of an RCD reduces the risk of
electric shock.
f)
Do not use the device if the power cord is damaged
or shows obvious signs of wear. A damaged power
cord should be replaced by a qualified electrician
or the manufacturer's service centre.
g)
To avoid electric shock, do not immerse the cord,
plug or device in water or other liquids. Do not use
the device on wet surfaces.
h)
ATTENTION! DANGER TO LIFE! While cleaning,
never immerse the device in water or other
liquids.
i)
Do not use in very humid environments or in the
direct vicinity of water tanks.
j)
Prevent the device from getting wet. Risk of
electric shock!
10
2.2. SAFETY IN THE WORKPLACE
a)
If you discover damage or irregular operation,
immediately switch the device off and report it to
a supervisor without delay.
b)
If there are any doubts as to the correct operation
of the device, contact the manufacturer's support
service.
c)
Only the manufacturer's service point may
repair the device. Do not attempt any repairs
independently!
d)
In case of fire, use a powder or carbon dioxide
(CO
) fire extinguisher (one intended for use on
2
live electrical devices) to put it out.
e)
Please keep this manual available for future
reference. If this device is passed on to a third
party, the manual must be passed on with it.
f)
Keep packaging elements and small assembly
parts in a place not available to children.
2.3. PERSONAL SAFETY
a)
When working with the device, use common sense
and stay alert. Temporary loss of concentration
while using the device may lead to serious
injuries.
b)
The device is not a toy. Children must be
supervised to ensure that they do not play with
the device.
c)
Do not put your hands or other items inside the
device while it is in use!
2.4. SAFE DEVICE USE
a)
Disconnect the device from the power supply
before commencement of adjustment, cleaning
and maintenance. Such a preventive measure
reduces the risk of accidental activation.
b)
When not in use, store in a safe place, away from
children and people not familiar with the device
who have not read the user manual. The device
may pose a hazard in the hands of inexperienced
users.
c)
Keep the device in perfect technical condition.
Before each use check for general damage and
especially check for cracked parts or elements
and for any other conditions which may impact
the safe operation of the device. If damage is
discovered, hand over the device for repair before
use.
d)
Device repair or maintenance should be carried
out by qualified persons, only using original spare
parts. This will ensure safe use.
e)
To ensure the operational integrity of the device,
do not remove factory-fitted guards and do not
loosen any screws.
f)
When transporting and handling the device
between the warehouse and the destination,
observe the occupational health and safety
principles for manual transport operations which
apply in the country where the device will be
used.
g)
Do not touch articulated parts or accessories
unless the device has been disconnected from the
power source.
h)
Do not move, adjust or rotate the device in the
course of work.
i)
Do not leave this appliance unattended while it is
in use.
j)
Clean the device regularly to prevent stubborn
grime from accumulating.
k)
Do not cover the air intake and outlet.
l)
The device is not a toy. Cleaning and maintenance
may not be carried out by children without
supervision by an adult person.
m)
It is forbidden to interfere with the structure of
the device in order to change its parameters or
construction.
n)
Keep the device away from sources of fire and
heat.
o)
Do not cover the ventilation openings!
p)
The device should be installed at a minimum
height of 1.8 meters from the floor.
ATTENTION! Despite the safe design of the
device and its protective features, and despite
the use of additional elements protecting the
operator, there is still a slight risk of accident or
injury when using the device. Stay alert and use
common sense when using the device.
3. USE GUIDELINES
The device is designed to heat the air in rooms. It
has a thermal protection that protects them from
overheating.
The user is liable for any damage resulting from
unintended use of the device.
3.1. DEVICE DESCRIPTION
3
2
1.
ON/OFF switch for standby mode
2.
Control panel with display
3.
Air outlet
Display / control panel:
1
9
2
8
7
3
4
5
6
1.
Value display
2.
Indicators of the desired heating power
3.
Program indicator
4.
ON/OFF button
5.
Heating power selection button
11
EN
6.
Timer button
7.
Open window detection indicator
8.
Timer indicator
9.
Temperature setting indicator
Remote control:
1
2
3
4
5
6
7
8
9
10
11
1.
ON/OFF button
2.
Timer button
1
3.
Settings programming button
4.
Heating power selection button
5.
Parameters decreasing (-)/increasing (+)/
confirming (OK) buttons
6.
Open window detection function button
7.
The Day-of-the-week setting button
8.
Program cancel button
9.
Switching on time setting button
10.
Program editing button
11.
Switching off time setting button
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The temperature of environment must not be higher
than 40°C and the relative humidity should be less
than 85%. Ensure good ventilation in the room in which
the device is being used. Keep the product away from
hot surfaces. The device should always be used when
positioned on an even, stable, clean, fireproof and dry
surface, and be out of the reach of children and persons
with limited mental and sensory functions. Position the
device such that you always have access to the power
plug. The power cord connected to the appliance must
be properly grounded and correspond to the technical
details on the product label. It is not allowed to mount
the device directly above the power socket! The device
must be installed at a height of min. 1.8 meters from the
floor of the room in which it will be used.
ASSEMBLING THE APPLIANCE
The device should be mounted on a vertical wall – for
this purpose, first attach two hangers on which hang the
device rigidly against the wall.
Publicité
Table des Matières
