Technical Data; Before Starting The Equipment - Bavaria 45.016.38 Mode D'emploi D'origine

Anleitung_BPC_1235_SPK7__ 03.11.15 10:11 Seite 21

4. Technical data

Engine displacement
Maximum engine capacity
Bar length
Cutter rail length
Chain pitch
Chain thickness
Idling speed
Maximum speed with cutting equipment
Chain speed max.
Tank capacity
Oil tank capacity
Anti-vibration function
Chain wheel teeth
Chain brake
Clutch
Automatic chain lubrication
Low-kickback chain
Net weight without chain and chain bar
Net weight (dry)
Fuel consumption (specific)
LPA sound pressure level (ISO 22868)
KPA uncertainty
LWA sound power level measured
(ISO 22868)
KWA uncertainty
LWA sound power level guaranteed
(ISO 2000/14/EC)
Ahv vibration (front handle)
(ISO 22867)
Khv uncertainty
Ahv vibration (rear handle)
(ISO 22867)
Khv uncertainty
Chain type
Bar type
Spark plug
Keep the noise emissions and vibrations to a
minimum.
n
37.2 cm 3
1.2 kW
n
n
33 cm
n
14" (35.56 cm)
n
(0.375"), 9,525 mm
n
(0.05"), 1.27 mm
n
3100 ± 300 rpm
12000 rpm

5. Before starting the equipment

22,9 m/s
310 cm 3
210 cm 3
is fully assembled.
Yes
6 teeth x 9.525 mm
when handling the chain.
Yes
Yes
5.1 Fit the chain bar
Yes
To ensure that the bar and the chain are supplied
with oil, USE ONLY THE ORIGINAL BAR. The oiling
Yes
hole (Fig. 2/Item A) must be kept clear of dirt and any
4.5 kg
build-up of residue.
5 kg 1. Make sure the Chain brake lever is pulled back
500 g / kWh
2. Remove the two bar fastening nuts (B). Remove
98.9 dB(A)
3 dB(A) 3. Using a screwdriver, run the adjustment screw (D)
107.8 dB(A)
4. Fit the open end of the chain bar over the die bar
3 dB(A)
114 dB(A)
5.2 To install saw chain
1. Spread chain out in a loop with cutting edges (A)
max. 6.74 m/s 2
2. Slip the chain around the sprocket (B) behind the
1.5 m/s 2
3. Guide the drive links into the groove (D) and
max. 5.53 m/s 2
1.5 m/s 2
NOTE: The saw chain may droop slightly on the lower
Sabre 91S053T
part of bar. This is normal.
Kangxin P014-50SR
NHSP LD L8RTF
4. Pull the chain bar forward until the chain is closely
5. Fit the clutch cover and fasten it with 2 screws.
Only use appliances which are in perfect working
order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever
necessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
Important: Do not start the engine until the saw
Important: Wear protective gloves at all times
into the DISENGAGED position (Fig. 3A)
the cover (Fig. 3B).
COUNTERCLOCKWISE until the TANG (E)
(projecting prong) is to the end of its travel toward
the clutch drum and sprocket (Fig. 3B/3C).
pins (F) (Fig. 3C/3D).
pointing CLOCKWISE around loop (Fig. 4A).
clutch (C). Make sure the links fit between the
sprocket teeth (Fig. 4B).
around the end of the bar (Fig. 4B).
seated. Make sure that all the drive links are in the
groove of the bar.
Make sure that the pivot (Fig. 3C/Item E) fits into
the chain bar (Fig. 3D/Item G). The chain must
GB
21