Zoning ZEBRA Manuel De L'utilisateur page 28

• Menu No. 17, activation of weekly programming. The
possible options are:
"0": weekly programming is deactivated, the indicator 6
lights up (fig. 3) and the temperature can be set
during operation by using the "UP" and "DOWN"
buttons
"1": the weekly programming defined in menu No. 1 is
activated and the indicators 7 and 8 light up (fig. 3).
If you wish, the temperature can be set during
operation by using the "UP" and "DOWN" buttons,
which will cause the indicator 6 to light up (fig. 3).
Do the following:
1 When you are already in programming menu No. 1,
press "UP" twice, which will take you to menu No. 3 for
temperature compensation.
2 Press "FAN" to enter this menu: the temperature digit
will appear flashing; using the "UP" and "DOWN"
buttons, select the desired value.
3 Press "FAN" to accept and the next menu will appear
(No. 4, screen backlighting).
4 Press "FAN" to enter the menu: the selection digit will
appear flashing; using the "UP" and "DOWN" buttons,
select the desired value ("ON": remains turned on;
"OFF": turns off after 15 seconds).
5 Press "FAN" to accept and the following menu will
appear (No. 5). Press "UP" to move forward to the
following menu (No. 6, fan control).
6 Press "FAN" to enter the menu: the selection digit will
appear flashing; using the "UP" and "DOWN" buttons,
select the desired value ("ON": fan active; "OFF": fan
inactive).
7 After selecting the desired option press "FAN" to accept
and the following menu will appear (No. 7, factory
values). Leave it on "OFF" to continue with the settings
(if you change it to "ON" it will return to the factory
settings).
8 Press "UP" to move forward to the following menu (No.
8, (Celsius or Fahrenheit).
26
Manual del usuario
User Manual
9 Press "FAN" to enter the menu and use the "UP" and
"DOWN" buttons to select the desired value (ºC or ºF).
10 Press "FAN" to accept and it will move on to the
following menu (No. 9, operating modes available
during use).
11 Press "FAN" to enter this menu: the digits of the options
will be flashing. Use the "UP" and "DOWN" buttons to
select the desired value.
12 Press "FAN" to accept and the next menu will appear
(No. 10, maximum temperature limit).
13 Press "FAN" to enter the menu and the temperature
digits will be flashing. Use the "UP" and "DOWN"
buttons to select the desired value (between 10ºC and
30ºC or 59ºF and 86ºF).
14 Press "FAN" to accept and the next menu will appear,
No. 11 (minimum temperature limit).
15 Press "FAN" to enter the menu and the temperature
digits will be flashing. Use the "UP" and "DOWN"
buttons to select the desired value (between 10ºC and
30ºC or 59ºF and 86ºF).
16 Press "FAN" to accept and the following menu will
appear (No. 12). Press the "UP" button twice and you
will move forward to menu No. 14 (button locking).
17 Press "FAN" to enter this menu and the digits of the
options will be flashing. Use the "UP" and "DOWN"
buttons to select the desired option (from "00" to "08").
18 Press "FAN" to accept and the next menu will appear
(No. 15, behaviour when the power supply is cut off).
19 Press "FAN" to enter this menu and the digit of the
options will be flashing. Use the "UP" and "DOWN"
buttons to select the desired option ("0": remain turned
off when the power supply returns; "1": return to the
status it was in when the power supply was cut off).
20 Press "FAN" to accept and the following menu will
appear (No. 16). Press the "UP" button to move forward
to the following menu (No. 17, activation of weekly
programming).
21 Press "FAN" to enter this menu and use the "UP" and
"DOWN" buttons to select the desired option ("0":
weekly programming
programming activated).
22 Press "FAN" to accept and you will exit this menu. Press
"MODE" and you will exit the settings menus.
V 12/17
deactivated; "1": weekly