Basic Settings (Fig. 17), To Be Carried Out Only By An Accredited Installer - Zoning ZEBRA Manuel De L'utilisateur

5 Once you have selected the minutes, press "FAN": the
temperature programmed for that timeslot will appear
flashing. Use the "UP" and "DOWN" buttons to select
the temperature you desire for the timeslot.
6 When you have selected the temperature, you will have
finished selecting all the settings corresponding to that
timeslot. Press "FAN": the daily timeslot will appear
flashing again. Use the "UP" and "DOWN" buttons to
select the next timeslot that you want to change.
Copying days (Fig. 16)
When you are carrying out the weekly programming (menu
No. 1), it is possible that you may want to programme some
days in exactly the same way as others.
In this case, the settings programmed for one day can be
copied to others, as shown below:
1 With the timer-thermostat turned off, press "FAN"
continuously for at least 5 seconds and the copying
days screen will appear. The original day to be copied
will appear flashing. Use the "UP" and "DOWN" buttons
to select the original day that you want to copy.
1
UP DOWN
Fig. 16 Copying days
I

Basic settings (Fig. 17), to be carried out only by an accredited installer

NOTE FOR USERS: this configuration must only be carried
out by an approved installer and must not be modified by
the user. Tampering with the unit may cause it to fail.
Basic configuration must be completed before using the
timer-thermostat. This configuration is carried out by
means of 2 menus:
• MASTER or SLAVE thermostat. Some operations can
only be carried out using the master (turn the complete
system on and off, etc.).
• Thermostat zone.
Advanced programming is carried out as follows (follow the
diagram in figure 17):
1 When you are already in programming menu No. 1,
press "UP" four times, which will take you to menu No.
5 for selecting MASTER/SLAVE.
24
Manual del usuario
User Manual
2
FAN
UP DOWN
7 Once you have selected the new timeslot to be
changed, press "FAN" and do the same as explained for
the previous timeslot.
8 When you have finished programming all the timeslots
for the day or group of days, press "MODE" so that the
digit for the day appears flashing. Use the "UP" and
"DOWN" buttons to select the new day to be
programmed and do that same as explained before.
9 When you have finished programming all the days,
press "MODE" to confirm and go back to the general
programming menu.
2 Press "FAN" to confirm and the day to be copied to will
appear flashing. Use the "UP" and "DOWN" buttons to
select the desired day to be copied to.
3 Press "FAN" to confirm the copy. It will move forward to
the next day to be copied to.
4 Continue copying in the same way if you wish to.
5 When you have finished copying press "MODE" and
copying days will be completed.
3
FAN
UP
2 Press "FAN" to enter this menu: the selection digit will
appear flashing; using the "UP" and "DOWN" buttons,
select the desired value (0: slave; 1: master).
3 Press "FAN" to accept and you will access the following
menu (No. 6).
4 Press "UP" six times and you will reach menu No. 12 for
selecting the zone number.
5 Press "FAN" to enter this menu: the selection digit will
appear flashing; using the "UP" and "DOWN" buttons,
select the value corresponding to the zone that this
thermostat will control (from 1 to 128).
6 Press "FAN" to accept and you will access the following
menu (No. 13). If you want to continue with the
programming, move forward through the menus using
the "UP" and "DOWN" buttons and when you reach the
desired menu, press "FAN" to access that menu.
7 If you want to exit the programming, press "MODE".
V 12/17
4
UP DOWN FAN
5
MODE
DOWN