Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
2007 WX 10000-1 4in1 v01.qxp
4/25/2008
Signal-ModulatedMonoChannel
SubwooferAmplifier
Congratulations on your
KICKER purchase
Please record your purchase
information and keep your sales
receipt for validation of warranty.
The Kicker Warhorse amplifier was specifically designed for competition car audio. Sporting 10,000
RMS watts of pure Kicker power, the ultra-high-efficiency design of the WX amplifier revolutionizes
traditional methods of amplification. While most amplifiers use a power supply combined with an
amplification circuit to amplify the audio signal, the Warhorse skips a step by amplifying the audio
signal directly from its patent pending signal-modulated power supply. The signal-modulated power
supply amplifies each polarity of the audio signal separately through its two voice coil outputs to
optimally drive dual-voice coil subwoofers and provide a competitive edge in SPL contests. From gold
plated power connectors and low profile planar transformers to the latest Texas Instruments DSP
technology, no expense was spared to make the Warhorse the most powerful and efficient mono
amplifier in mobile audio.
The patent pending signal-modulated
design of the Warhorse amplifier is the
most powerful and efficient design
available in mobile audio, rated at 90%
efficiency at full power with a 2 ohm load.
The graph compares the Warhorse
amplifier's efficiency ratings to those of
industry standard Class D amplifiers.
Installation
. . . as easy as 1, 2, 3
1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The amplifier should
be mounted as close as possible to the battery network and be electrically isolated from the vehicle
ground. The distance from the battery network to the amplifier should not exceed 48" (122cm). It is
important to mount the amplifier before running any wires or supplying power to the amplifier. The
amplifier secures to the vehicle with an insertable mounting bracket used in combination with two
mounting holes located on the bottom plate of the control panel. You are solely responsible for securely
fastening the WX amplifier in your vehicle.
Before mounting the amplifier, the control panel shield must be removed. The control panel should
remain accessible for adjustment, leaving enough room to access the mounting holes and remove or
attach the control panel shield. Make sure there are no items behind the area where the screws will be
driven. Choose a location that allows at least 4" (10cm) of open ventilation for the amplifier. After
choosing the best location, secure the mounting bracket to the vehicle. Use the bracket as a template
to drill nine (9) holes with a 3/16" (4.8mm) bit into the appropriate locations. Attach the bracket to the
mounting location with the nine (9) supplied #10 (5mm) screws inserted through the nine (9) included
screw insulators.
Next, slide the amplifier over the mounting bracket and into the mounting slot. Make sure the mounting
bracket is properly inserted into the mounting slot and locate the two mounting holes on the bottom
plate of the control panel. Use the mounting holes as a template and drill two (2) holes using a 3/16"
(4.8mm) bit into the appropriate locations. Secure the bottom plate of the control panel with the two (2)
#10 (5mm) screws.
Caution The Kicker WX amplifier outputs extremely high voltage signals
from the voice coil (speaker) outputs and can cause serious injury or death
from electrocution. It is imperative to read the manual carefully and follow all
of the recommended safety precautions before installing the WX amplifier.
WX10000.1AMPLIFIER
2
1:46 PM
Page 2
WX.1SeriesAmplifier
Owner'sManual
Model:
WX10000.1
__________________________
Authorized Kicker Dealer:
__________________________
Purchase Date:
WX10000.1
__________________________
Amplifier Model Number:
__________________________
Amplifier Serial Number:
Figure 1
100
80
60
40
KICKER PATENT PENDING SIGNAL-MODULATED DESIGN
20
HIGH QUALITY CLASS D DESIGN
0
0.1
0.2
0.5
1.0
2.0
4.0
8.0
POWER OUTPUT (KW)
Before mounting the amplifier, be sure there is adequate space in the mounting position
Figure 2
to take the control panel shield on or off and to easily access the amplifier's controls.
1.
Remove the two (2) screws
securing the control panel
shield to the amplifier chassis.
2.
Remove the control panel shield from the
amplifier so the mounting holes on the bottom
plate of the control panel will be accessible.
3.
After determining the best mounting position for the amplifier, use the mounting bracket as a template to drill
nine (9) holes with a 3/16" (4.8mm) bit into the appropriate locations. Attach the bracket to the mounting
location with the nine (9) supplied #10 (5mm) screws inserted through the nine (9) included screw insulators.
Nine (9) Supplied
Screw Insulators
90%
75%
Nine (9) Supplied
#10 (5mm) screws
4.
Slide the Warhorse over the mounting bracket and insert the mounting
bracket into the mounting slot on the bottom of the amplifier.
10
Mounting Bracket
5.
Locate the additional mounting holes on the bottom plate of the control panel. Use the mounting holes as a template
to drill two holes using a 3/16" (4.8mm) bit into the appropriate locations. Secure the bottom plate of the control panel
with the two (2) #10 (5mm) screws. You are solely responsible for securely fastening the amplifier in your vehicle.
Control Panel Shield
Mounting Bracket
Warhorse Amplifier
The amplifier is very heavy.
Assistance may be necessary
to lift and position the amplifier.
Mounting Holes
Control Panel
(Top View)
3
Publicité
Table des Matières
