Before Starting The Equipment; Replacing The Power Cable; Practical Tips; Cleaning, Maintenance And Ordering Of Spare Parts - Bavaria BPL 600 Mode D'emploi

Masquer les pouces Voir aussi pour BPL 600:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 14
Anleitung BPL_600_SPK1:_
GB

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
5.1 Adjusting the chip depth (Fig. 4/Item 1)
You can adjust the chip depth in steps of 0.25 mm
from 0 to 2 mm by turning the setting knob for the
chip depth (1).
Turn the setting knob for the chip depth (1) in a
clockwise direction to set a greater chip depth.
Greater chip depth
Turn the setting knob for the chip depth (1) in a
counter-clockwise direction to set a lower chip depth.
Lower chip depth
After finishing work, set the chip depth so that the
knives are lowered and thus protected from damage.
Turn the setting knob for the chip depth to position
"0" for this purpose.
5.2 Chip extraction (Figure 5)
For optimum chip extraction connect the hand-held
electric plane to a dust extraction system using the
supplied adapter piece.
Slide the adapter piece into the chip ejector on the
side of the hand-held electric plane. Now you can
connect a suitable dust extraction system to the
round connector of the adapter piece.
6. Operation
6.1 ON/OFF switch (Fig. 6)
The hand-held electric plane comes with a safety
switch which is designed to prevent accidents.
To switch on the tool press the side safety lock-
off (3) and press the button switch.
Release the button switch (2) to switch off the
electric plane. The button switch (2) jumps back
into its starting position.

6.2 Practical tips

Important: Only ever bring the hand-held electric
plane towards the workpiece while switched on.
12
16.04.2009
13:34 Uhr
Seite 12
6.2.1 Planing surfaces
Now adjust the desired chip depth. Equip the front
base plate and place the hand-held electric plane
onto the piece of wood you whish to plane. Then
switch on the plane. Push to electric plane over the
surface with both hands and make sure that the both
the front and the rear base plate lie flat on the
workpiece.
Used a low chip depth for finishing surfaces and
complete several passes over the surface.
6.2.2 Chamfering edges (Fig. 7-8)
There is a V-shaped groove (a) in the front base
plate that enables you to plane edges at an angle
of 45° for a smooth finish.
Switch on the tool and wait until it reaches full
speed. Place the V-shaped groove (a) on the
edge of the workpiece at an angle of 45°.
Now move the electric plane along the edge of
the workpiece.
To achieve a good quality result you should keep
the feed speed and angle constant.

7. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
8. Cleaning, maintenance and ordering
of spare parts
Always pull out the mains power plug before starting
any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts
of the equipment. Ensure that no water can seep
into the device.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

43.452.21

Table des Matières