Victron energy MultiPlus 12/3000/120-16/230/240V Manuel page 19

5.5.1.5 Examples
examples of settings:
DS-8 AC input on
DS-7 AC input on
DS-6 AC input on
DS-5 AES off
DS-4 Ch. current on
DS-3 Ch. current off
DS-2 N/A off
DS-1 N/A off
Step 1, Example 1 (factory Step1, Example 2:
setting):
8, 7, 6 AC-in: 50A* 8, 7, 6 AC-in: 50A*
5 AES: off 5 AES: off
4, 3 Charging current: 75% 4, 3 Charge: 100%
2, 1 N/A 2, 1 N/A
*Maximum is limited to 16A in case of models with 16A transfer switch
To store the settings after the dipswitches are set according to the required values: press the 'Up' button for 2 seconds (upper button to
the right of the DIP switches, see appendix A, position J). The overload and low-battery LED's will flash to indicate acceptance of
the settings.
We recommend making a note of the settings, and filing this information in a safe place.
The DIP switches can now be used to apply the remaining settings (step 2).
5.5.2 Step 2: Other settings
The remaining settings are not relevant for slaves.
Some of the remaining settings are not relevant for followers (L2, L3). These settings are imposed on the whole system by the leader
L1. If a setting is irrelevant for L2, L3 devices, this is mentioned explicitly.
ds8-ds7: Setting charging voltages (not relevant for L2, L3)
Absorption Float
ds8-ds7
voltage oltage
14.1 13.8
off off 28.2 27.6
56.4 55.2
14.4 13.8
off on 28.8 27.6
57.6 55.2
14.7 13.8
on off 29.4 27.6
58.8 55.2
15.0 13.8
on on 30.0 27.6
60.0 55.2
ds6: absorption time 8 or 4 hours (na for L2, L3)
ds5: adaptive charging algorithm (na for L2, L3)
ds4: dynamic current limiter
ds3: UPS function
ds2: converter voltage
ds1: converter frequency (na for L2, L3)
(the wide input frequency range (45-55Hz) is 'on' by default)
Note:
- If "adaptive charging algorithm" is on, ds6 sets the maximum absorption time to 8 hours or 4 hours.
- If "adaptive charging algorithm" is off, the absorption time is set to 8 hours or 4 hours (fixed) by ds6.
DS-8 on DS-8
DS-7 on DS-7 on
DS-6 on DS-6 on
DS-5 off DS-5
DS-4 on DS-4 on
DS-3 on DS-3 on
DS-2 off DS-2
DS-1 off DS-1
Step1, Example 3:
8, 7, 6 AC-in: 16A
5 AES: off
4, 3 Charge: 100%
2, 1 N/A
Storage
voltage
13.2 Gel Victron Long Life (OPzV)
26.4 Gel Exide A600 (OPzV)
52.8 Gel MK battery
Gel Victron Deep Discharge
13.2
Gel Exide A200
26.4
AGM Victron Deep Discharge
52.8
Stationary tubular plate (OPzS)
AGM Victron Deep Discharge
13.2
Tubular plate traction batteries in
26.4
semi-float mode
52.8
AGM spiral cell
13.2
Tubular plate traction batteries or
26.4
OPzS batteries in cyclic mode
52.8
off DS-8 on
DS-7 on
DS-6 off
off DS-5 on
DS-4 off
DS-3 on
off DS-2 off
off DS-1 off
Step1,Example 4:
8, 7, 6 AC-in: 30A*
5 AES: on
4, 3 Charge: 50%
2, 1 N/A
Suitable for
on = 8 hours off = 4 hours
on = active off = inactive
(inactive = fixed absorption time)
on = active off = inactive
on = active off = inactive
on = 230V off = 240V
on = 50Hz off = 60Hz
17