Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
KV10.5 12 Volt DC ELECTRIC WINCH
Designed for Vehicle Recovery, Vehicle Trailers and General Winching Applications.
THIS PRODUCT IS NOT INTENDED FOR LIFTING/HOISTING
Assembly & Operating Instructions
!
!
CAUTION
PLEASE READ ALL SAFETY PRECAUTIONS AND WARNINGS BEFORE INSTALLING AND USING THE WINCH! IF
YOU HAVE ANY QUESTIONS PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT LISTED BELOW.
Introduction
Thank you for purchasing your KEEPER
PLEASE READ ALL INSTRUCTIONS, PAYING SPECIAL ATTENTION TO THE SAFETY INSTRUCTIONS.
Your KEEPER
Winch has been designed and manufactured to provide years of trouble-free operation.
®
If you are not satisfied, for any reason, please contact Customer Service at 800-533-7372, visit our website: www.keeperwinches.com or contact
keeperwinches@hamptonproducts.com. When requesting information in regard to this winch, please give the following information:
Winch Part #____________________ and Serial number___________________________________.
(Please write down this information here for future reference.) (Found on Motor Housing)
Please read and understand this Owner's Manual prior to installing and operating this product. PAY PARTICULAR ATTENTION TO THE GENERAL SAFETY
INFORMATION. Your Winch is a powerful machine. If used unsafely or improperly, there is a possibility that property damage and/or personal injury can result.
Your safety ultimately depends on your caution when using this product.
General Description
This KEEPER
Winch is equipped with a series wound, 12 Volt DC motor and is
®
designed for INTERMITTENT GENERAL DUTY USE. This electric winch is similar to
most electric motor driven tools and should not be allowed to become overly hot.
Stop winch if motor starts to labor or end of motor becomes hot to the touch.
Stop winching and allow motor to cool down.
Minimum electrical requirements are 60 amp alternator
and battery with 650 CCA (cold cranking amp) capacity.
This Winch (FIGURE 1) is not intended for use in
lifting/hoisting applications and the manufacturer
does not warrant it to be suitable for such use.
The Freespool Clutch disengages the gearbox to allow
the wire rope to be pulled out without using electric power.
A Remote Switch with 15' lead allows a wide variety
of mounting options.
Wire Cable Assembly is 85' X 3/8". Usable length is 80 feet.
Wiring harness to battery length is 6 feet.
Performance
KV 10.5 SPECIFICATIONS
Part Number:
KW10022
Rated Line Pull:
10,500 lbs., 4,763 kg.
Motor - Series Wound:
5.5HP 12V DC
Control:
Hand Held Remote on 15' lead with built-in High Density Light
Switching:
High Duty cycle Sealed Solenoid Pack
Gear Train:
High Efficiency 3-Stage Planetary Gear Set
Gear Reduction:
265:1
Clutch (Freespooling):
Sliding Ring Gear
Brake:
Mechanical Automatic Cam Activated
Wire Rope:
85' (26 m) of 3/8" (9.5 mm) Diameter Galvanized Wire Rope with
Looped Thimble, Latched Clevis Hook and Red Warning Area.
Drum Diameter/Length:
Diameter - 2.5" (63.5 mm) / Length - 8.8" (224 mm)
Fairleads:
4-way Roller Fairlead
Battery Leads:
2 Gauge, 72" (1.83 m)
Minimum 650 CCA
Battery:
Application:
General Utility Load Recovery/Trailer, Truck, Tractor, Equipment
Finish:
High-Gloss gray Powder Coat over Undercoating
Weight:
96 lbs. / 43.6 kg.
Winch.
®
THIS PRODUCT IS NOT INTENDED FOR LIFTING / HOISTING
FIGURE 1
*DOES NOT INCLUDE MOUNTING PLATE
2
Publicité
Table des Matières
