Table des Matières
Publicité
Instruction Manual
EK 60UNV-L
4.2 Explanation of the application range
The electric hydraulic unit can be operated with a large
number of various crimping and cutting dies.
Attention
Do only crimp those connecting materials men-
tioned in Tab. 2 and 3.
If different conducting materials have to be crimped, ple-
ase contact the manufacturer.
Attention
Do not crimp on live cables or conduc-
tors.
The unit is a hand held tool and it is not supposed to be
restrained in a vise. It is not allowed to use the tool in a
stationary application.
The tool is not designed for continued operations. After
a sequence of approximately 50 completed cycles you
have to make a break of 15 min. to give the tool time to
cool down.
Attention
Too intensive use can cause heat damages for
the tool
Attention
During the operation of electric engines sparks
can occur which might ignite highly infl ammab-
le or explosive liquids and materials
Attention
Electric-hydraulic tools should not be operated
in pouring rain or under water.
4.3 Mounting instructions
Please read the assembly instructions in our general ca-
talogue.
Attention
Even if the code number is identical only those
dies should be used which are suitable for the
material.
4.4 Service and maintenance instruction
The electric-hydraulic unit is equipped with a controller
enabling the user to see when the next service is due.
When the next service is due the unit must be returned to
an authorised service center.
For every day service the unit has to be cleaned and dried
after each use. The battery cartridge and the charging unit
have to be protected against humidity and dust.
Within the determined use of the tool only the dies, the
adapters are permitted to be changed by the customers.
Attention
Do not damage the seals of the tool. If the seals
are damaged the warranty is invalidated.
5.
Troubleshooting
a.) Constant fl ashing/indicating of the light diode display
(pic 1.3) .
see table 1. If the failure can not be solved return the
tool to the nearest service center (ASC).
b.) The tool loses oil.
Return the unit to the manufacturer. Do not open it and
damage the seal of the tool.
HE.13423_B © 09/2010
6.
Technical Data
Weight
approx. 4,7 kg
(incl. battery):
Crimping force:
approx. 60 kN
Stroke:
42 mm
Battery voltage:
18 V
Battery capacity
3 Ah (RAL2/BL1830)
Charging time:
22 min. (RAL2/BL1830)
Crimping time:
approx. 5 s to 8 s
(depending on the connector size)
Crimps
approx. 300 crimps
per battery:
(Cu 150 mm² DIN 46235)
Max. cutting
40 mm Ø
diameter:
Cutting time:
8 s to 20 s
(depending on the cable size)
Cuts per battery: approx. 75 cuts (4x70 mm² NYY)
Punching time:
5 s with 22,5 mm Ø, 3 mm St37
12 s with 60 mm Ø, 3 mm St37
Capacity:
• 60 cycles per battery
with 60 mm Ø in 3 mm mild steel
• 170 cycles per battery
with 22,5 mm Ø in 3 mm mild steel
Hydraulic oil:
Rivolta S.B.H. 11
Environmental
-20°C to +40°C
temperature:
Sound level:
70 dB (A) in 1m distance
Vibrations:
< 2,5 m/s²
7.
Putting out of operation/waste dis-
posal
This unit is subjected to the scope of the European WEEE
(2002/96/EG) and RoHS (2002/95/EEC) directives.
Information about this can be found on our home page
www.Klauke.com under 'WEEE & RoHS'.
Battery cartridges (page I, pic. 1, 3) must be specially dis-
posed of according to the EEC Battery Guideline.
Attention
Do not dispose of the unit in your residential
waste. Klauke has no legal obligation to take
care of their WEEE outside Germany unless the
product has been shipped and invoiced from
inside your country by Klauke. Please contact
your distributer to fi nd out more how to get your
tool recycled environmentally friendly.
Attention
Additional instruction manuals are available
free of charge. The part # is HE.13423.
3
GB
Publicité
Table des Matières
