AudioSonic CD-1588 Mode D'emploi page 4

PLAY A CD
1. Make sure the power is connected, slide the FUNCTION switch to CD/MP3 position,
POWER indicator will light.
2. Load a disc into the CD compartment. Close the CD door, the disc will begin to spin.
3. Adjust the VOLUME to the desired volume level.
4. To stop playing temporarily, press the PLAY/PAUSE button.
The elapsed time of the current track flashes and an icon of "PAUSE" appears on the
Ÿ
bottom of the LCD to indicate the player is in pause mode.
Ÿ Resume normal play by pressing PLAY/PAUSE button again.
5. To stop playing, press the STOP button. The total tracks' number and whole playing time
with an icon "STOP" on the bottom will be shown on the display.
6. To turn off the player, slide the FUNCTION switch to OFF position.
EQ SELECTION
Press EQ/Program button continuously during disc playback mode to select EQ sound
effects among NORMAL, POP, ROCK, CLASSIC, JAZZ and BASS.
SKIP TRACKS AND SEARCH FOR A SPECIFIC POINT TO PLAY
1. Press once the SKIP/SEARCH up button in music play to skip to the next track. To skip
to a specific track ahead, press this button several times.
2. Press once the SKIP/SEARCH down button in music play to skip to last track. To skip to
a specific track at back, press this button several times.
3. Press +10/ALBUM button once in play to skip to the track 10 tracks ahead, twice to skip
to the track 20 tracks ahead. You can reach the last track of the disc using this button.
4. Hold the SKIP/SEARCH up button in music play to search forward at quick rate for a
Specific point to play.
5. Hold the SKIP/SEARCH down button in music play to search backward at quick rate for
a specific point to play.
PROGRAMMED PLAY
Programmed play is that tracks on the disc can be edited for playback in a preferred order
with the use of PROGRAM button.
In CD stop mode, press EQ/PROGRAM button once, "PROG" shows in the LCD with a
flickering track number and the program sequence indication "P-01", select the first track to
be programmed using SKIP/SEARCH buttons, and press EQ/PROGRAM button again to
store and advance to the next programming step. The program sequence indication
changes to "P-02" waiting for your next input.
Repeat the steps above to program more tracks. A maximum of 20 tracks can be
programmed in memory in a preferred order.
Press PLAY/PAUSE button to begin programmed play in the preferred order after you are
done with programming. The player stops automatically after all programmed tracks are
played.
You may press STOP button to terminate programmed playback. In program stop mode,
press STOP button again to clear the programming; press PLAY/PAUSE button to begin
the programmed playback with the programming order identical with the previous one done.
REPEAT A SINGLE TRACK
To repeat a preferred track in playback, press MODE button once, the LCD shows the icon
for single track repeat. Then select the preferred track using SKIP/SERCH buttons or
+10/ALBUM button. The player will repeat the chosen track until you press STOP button.
GB-5
REPEAT ALL TRACKS
To repeat all tracks, press MODE button twice in play mode,
tracks repeat. The player will repeat all tracks until you press STOP button.
RANDOM PLAY
Random play is that tracks on the disc are played by the player at random. Press MODE
button three times to enter this mode during play, "RAN" shows in the LCD. Press
Play/Pause button or SKIP buttons to begin Random playback. Tracks on the disc will be
selected at random for playback and the player stops automatically after all tracks are
played. Press MODE button once more to exit random.
INTRODUCTION PLAY
Introduction play is that the first ten seconds of each track are played in a sequential order.
Press MODE button four times to enter this mode during play, "INTRO" shows in the LCD.
Press Play/Pause button to begin Introduction play from Track NO.1. Press SKIP up button
to begin INTRO playback from the track immediately after the current track and SKIP down
button to begin INTRO playback from the
playback to exit Introduction play mode and press play/pause button to resume normal
music play.
MP3-CD (WMA) PLAYBACK
This player is capable of MP3-CDs. It takes longer time for this player to read an MP3-CD
than it does CD-DA. Wait patiently while it is reading.
After an MP3-CD is successfully read, the total number of albums and tracks show on the
LCD. And a second later, playback begins from the first track of the first album with the Mp3
icon.
LOCATE A TRACK OR ALBUM AND SEARCH FOR A SPECIFIC POINT TO PLAY
1. Press once the SKIP/SEARCH up button in music play to skip to the next track. To skip
to a specific track ahead, press this button several times.
2. Press once the SKIP/SEARCH down button in music play to skip to the last track. To
skip to a specific track at back, press this button several times.
3. Press +10/ALBUM button once in play to skip to the track 10 tracks ahead, twice to skip
to the track 20 tracks ahead. You can reach the last track of the current album using this
button.
4. Hold the SKIP/SEARCH up button in music play to search forward at quick rate for a
specific point to play.
5. Hold the SKIP/SEARCH down button in music play to search backward at quick rate for
a specific point to play.
6. Hold the +10/ALBUM button, the album number will flash; press the Skip/Search button
to select the desired album, press and hold the ALBUM button again for 2 seconds to
confirm this album selection, the track number flickers for your input; select the desired
track of the chosen album using the SKIP/SEARCH buttons. Finally, press PLAY/PAUSE
button again to begin playing this chosen track.
REPEAT A SINGLE TRACK
To repeat a preferred track in playback, press MODE button once,
for single track repeat. Then select the preferred track using SKIP/SERCH buttons. The
player will repeat the chosen track until you press STOP button.
the LCD shows the icon for all
previous track. Press STOP button in Intro
the LCD shows the icon
GB-6