Before Starting The Equipment; Wall Mounting; Remote Control - EINHELL EF 1800 Instructions D'origine

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
5.1 Wall-mounting
Caution!
In order to avoid breaking the glass, remove the
glass front panel from the equipment and only fi t it
back in place again at the end.
The minimum clearances must be observed. The
equipment is allowed to be used only when it is
completely assembled and in a vertical position.
(Fig. 3) Ensure that a minimum clearance of 20
cm to the sides, 100 cm to the ceiling, 60 cm to
the fl oor and 100 cm to the front of the housing
are maintained. Observe point 1 - Safety infor-
mation.
Caution! Make sure that there are no electric
cables or other installations (for example water
pipes) near the drill holes. Ensure that the equip-
ment is secured fi rmly and horizontally to the wall.
Use only suitable fastening material on a wall
capable of bearing the load. The supplied dowels
and screws are suitable for the following: Con-
crete, natural stone with a dense structure, solid
brick, solid limestone bricks, solid lightweight
concrete bricks and aerated concrete.
1. Fig. 4: Mark the positions of the four drill holes
for the top wall bracket (11) horizontally on
a wall capable of bearing the load. The drill
holes are arranged 150 mm apart.
2. Then drill four holes (Ø 6 mm) in the wall and
insert the dowels (Fig. 2/Item 13). Place the
holes in the top wall bracket (Fig. 4/Item 11)
over the drill holes and secure the wall bra-
cket using 4 screws 4x30 mm (Item 14). En-
sure that the hooks on the wall bracket point
upwards (Fig. 4).
3. Fig. 5: Fit the fi xing bracket (12) using two 4x8
mm screws (Fig. 2/Item 15) to the middle on
the underside of the heater housing.
4. Fig. 6: Hang the housing on the wall bracket.
Ensure that the hooks on the wall bracket
latch into the holes in the housing (A).
5. Fig. 5: Transfer the holes (B) in the fi xing bra-
cket (12) to the wall and remove the heater
housing again.
Anl_EF_1800_SPK9.indb 22 Anl_EF_1800_SPK9.indb 22
GB
6. Drill two holes (Ø 6 mm) in the wall, insert the
dowels (Fig. 2/Item 13) and hang the housing
on the top wall bracket again (Fig. 6). Ensu-
re that the hooks latch into the holes in the
housing (A).
7. Fig. 5: Secure the fi xing bracket using two
4x30 mm screws (Fig. 2/Item 14) to the wall.
8. Fig. 7: Arrange another person to help you
and hang the glass front panel (1) in the slots
(C) provided on the housing by the hooks pro-
vided on the side of the glass front panel.

5.2 Remote control

Note: All modes and functions can be set using
the buttons on the appliance as well as with the
remote control. The remote control requires a CR
2025 button cell (included in the remote control).
Pull the contact protection (small plastic plates)
out of the housing before use.
Important! It may take a few seconds for the
equipment to react when you press the buttons
on the remote control. Do not press the buttons
on the remote control repeatedly within 2 se-
conds.
•
Never use a battery type other than the spe-
cified one.
•
If the remote control is not used for a lengthy
period of time, remove the battery to prevent
it leaking.
•
Point the remote control towards the heater.
The range is max. 5 meters.
•
Direct sunlight and objects can considerably
reduce the range of the remote control.
•
Handle the remote control with care. Do not
drop it and keep it away from heat and mois-
ture.
Inserting the battery (Fig. 8):
1. Open the battery compartment cover by
pressing the lock (F) towards the middle and
pulling the battery compartment out at the
same time.
2. Make sure you fi t the battery with the + and
– terminals correctly positioned as shown on
the housing.
3. Press the battery compartment cover into the
remote control.
As the end user you are legally required to return
spent batteries. You can hand them in at public
collection points provided by your council or sales
outlets where batteries of this type are sold. Ob-
serve the instructions in section 11 as well.
- 22 -
22.11.2018 06:58:50 22.11.2018 06:58:50