Bosch GTA 3800 Professional Notice Originale page 16

16 | English
(20) Transport wheels fastening set
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Saw stand
Article number
Length of saw stand without
table extension
Length of saw stand with table
extension
Saw stand height
Max. load bearing capacity (power tool + workpiece)
without table extension
– Holder sets
Max. load bearing capacity (power tool + workpiece) with
table extension
– Holder sets
– Per table extension
Weight according to EPTA-Pro-
cedure 01:2014
Assembly
Items included
See the list of items included at the start of
the operating manual.
Check to ensure that all the parts listed below have been
supplied before assembling the saw stand:
No. Designation
GTA 3800 saw stand
(4) Holder set
(1) Workpiece support
(7) Roller support
(14) Socket spanner (13 mm)/hex key
(4 mm)/cross-headed screwdriver
(19) Power tool fastening set consists of:
– Hexagon screw (M8 x 45)
– Washer
Extra tools required (not included in the delivery):
– Open-end spanner (10 mm)
Installing the Saw Stand
Carefully remove all parts included in the delivery from their
packaging.
Remove all packing material.
1 609 92A 6JA | (24.08.2021)
a) Setting up the saw stand (see figures A1−A2)
– Place the saw stand on the floor with legs up.
– Press the locking pin (15) in and swivel the leg up until
– Repeat this work step with the other three legs.
– Rotate the saw stand into the working position.
GTA 3800
– Make sure that the saw stand is stable and all locking pins
3 601 M24 001
– A height-adjustable foot (9) helps you to align the saw
mm 1578
– Screw the foot in or out until the saw stand is level and all
mm 3877
Installing roller support (see figure B1)
mm 824
– Unscrew the cross-head screw of the roller support (7)
kg 250
– Remove the roller support (7).
There are various options as to how the individual rollers can
kg 150
be arranged on the workpiece support using the internal
kg 50 threaded rod.
– Arrange the individual parts as required and push the in-
kg 22.4
– Screw all parts back together.
Installing workpiece support (see figure B2)
– Release the locking knobs (3) and pull the table
– Push the workpiece supports (1) from left and right re-
– The length stops (8) must point outwards here.
– Pull the locking knob (6) to lock the workpiece support.
Preparing the Saw Stand
Quantity
Preparing holder sets (see figures C1–C4)
1
– To unlock the holder sets (4), press the buttons (16) and
2
2
– Measure the distance x between the assembly holes on
2
1
– Position the holder sets (4) in the centre of the saw stand
– Close each lever (17) again. This allows the holder sets to
4
4 Setting up the saw stand (see figure D)
– Bring the power tool into the transport position. Informa-
– Position the movable nuts (18) in the holder sets so that
– Screw using the supplied socket spanner (14) holder set
the locking pin audibly engages again.
have engaged.
stand.
four legs are on the ground.
with the supplied cross-headed screwdriver (14).
If required, resist the lock nut on the other side of the
roller support with an open-end spanner (10 mm).
ternal threaded rod through the rollers and through the
workpiece support (1).
extensions (2) slightly out on both sides of the saw stand.
spectively into the upper groove of the saw stand or the
table extension.
open the levers (17) respectively.
your power tool.
and at the appropriate distance x from each other.
be firmly positioned on the saw stand.
tion about the transport position can be found in the op-
erating instructions for the corresponding power tool.
they match the assembly holes on the power tool.
and power tool with the hexagon screws and washers
from the fastening set (19).
Bosch Power Tools