Oscartielle Argus Mode D'emploi page 23

The following technical data are also shown on the serial plate (FIG. 8):
1. Commercial name of the refrigerating display unit
2. Refrigerating display unit code
3. Refrigerating display unit serial number
4. Rating
5 . Frequency
6. Max absorbed current
7. Max absorbed power
8. Max absorbed power during defrosting
9. Standard lighting power
10. Net display area
11. Type of cooling gas used
12. Weight of cooling gas loaded in each unit
13. Climatic class and reference temperature (dry bulb)
14. Electrical safety factor
15. Work schedule number
16. Work order number
17. Year of manufacture
W arning: The serial plate and the warning labels must never be removed from the cabinet. The Manufacturer is not liable
for any damage or injury
degree no. 108 dated 25.01.1992, applying EEC
contact with food.
7 - Loading and use of the unit (s
If the display unit has been greatly tilted during positioning and installation, wait at least three hours before starting it up in
order to give the lubricating oil
d amaged if this precaution is ignored. The display unit can only be started up for the very first time after complying with
points 3 and 4 above.
With the unit unplugged, remove the plastic film protecting the insides and outsid
in point 10 below). Screw on the back spacers as s
as shown in FIG. 12 and FIG. 12B (only for Phoenix 2). FIG. 1 shows the best distances between shelves. Plug in the
unit (having followed the instructions in point 5), then switch on the lights and motor unit
panel (see FIG. 10). The gentle hum of the motor and illumination of the display will indicate that the cabinet is working.
The thermometer inside the display unit (see FIG. 10) will indicate the working temperature. The instruction manual for
the electronic control to which the display refers is enclosed with the instruction booklet (tampering with this device is
impossible because a password is required and only a specialized expert can intervene on it). The thermostat and gas
charge are set in the factory. Tampering with the factory settings relieves the manufacturer of any liability. Always check
that the temperature reading on the display of the electronic control is suitable for the conservation of the products placed
in the display cabinet.
The unit is designed to display food products and to maintain the temperature of the product; it does not lower it. The
product should, therefore, only be loaded once its proper storage temperature has been reached. Recommendations for
storage:
- Never block the cooling outlets that guarantee the correct flow of air (see FIG. 13).
- When loading a display cabinet that already contains products, it is best to place the new products below those
already inside (as well as observing the a
- At night, use the night blinds (avail
display.
8 - Prohibitions and requirements
Warning: disconnect the cabinet from the power supply in case it is n
by the remote-control switch fitted upstream from the pow
Warning: Never expose the unit to the atmospheric agents. Never use direct water jets to clean the
use the unit with wet or damp feet and hands.
Warning: Never remove guards or covers that require tools to be removed. Never,
cover on the electronic panel.
Warning: Never load the unit excessively. Never go inside the cabinet.
Warning: Never stand on the unit or place heavy loads on top of the cabinet.
Warning: Never try to remove any ice that may build up using sharp metal objects.
Warning: The refrigerating circuit does not cause any chemical
c omes exclusively from the vapour contained in the air circulating inside the unit. In any case, this water should always be
drained into the sewe r or sent to a water purification plant in line with current local regulations.
Warning: Any use of the unit not explicitly mentioned in this manual should be consid
Manufacturer is not l iable for any damage resulting from improper, careless or unreasonable use.
Warning: Do not dam age the refrigerant circuit (IEC60335-2-89:2002 and changes)
Warning: Do not use electrical appliances inside the food
type recommended by the
if this warning is ignored. The Manufacturer certifies that this unit complies with Italian legislative
tart-up)
enough time to collect in the compressor! The refrigerating unit may be irretrievably
bove points).
able on request), as this will save energy and help preserve the products on
manufacturer (IEC60335-2-89:2002 and changes)
Directive 89/109 concerning materials and objects that come into
hown in FIG. 11. Fit the various shelf supports at the height required,
ot used. The power supply has to be disconnected
er socket.
modification of the water generated from defrosting. This
storage compartments of the appliance, unless they are of the
e and then clean (follow the instructions
located under the decorative
unit. Never touch or
under any circumstances, remove the
ered dangerous and the
21