Product Description And Specifications; Technical Data; Noise/Vibration Information - Berner BACSDB-1 18V Notice Originale

Use suitable detectors to determine if there
u
are hidden supply lines or contact the local
utility company for assistance. Contact with
electric cables can cause fire and electric
shock. Damaging gas lines can lead to explo-
sion. Breaking water pipes causes property
damage.
Hold the power tool securely. When tightening
u
and loosening screws be prepared for tempor-
arily high torque reactions.
In case of damage and improper use of the
u
battery, vapours may be emitted. The battery
can set alight or explode. Ensure the area is
well ventilated and seek medical attention
should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of
u
short-circuiting.
The battery can be damaged by pointed ob-
u
jects such as nails or screwdrivers or by
force applied externally. An internal short cir-
cuit may occur, causing the battery to burn,
smoke, explode or overheat.
Only use the battery with products from the
u
manufacturer. This is the only way in which you
can protect the battery against dangerous over-
load.
Protect the battery against heat, e.g.
against continuous intense sunlight,
fire, dirt, water and moisture. There is
a risk of explosion and short-circuiting.
Product Description and
Specifications
English
Read all the safety and general in-
structions. Failure to observe the
safety and general instructions may
result in electric shock, fire and/or ser-
ious injury.
Please observe the illustrations at the beginning
of this operating manual.
Intended use
English
The power tool is intended for driving and loosen-
ing screws and for drilling in wood, metal, ceramic
and plastic.
Product features
English
The numbering of the product features refers to
the diagram of the power tool on the graphics
page.
(1) Tool holder
(2) Keyless chuck
(3) Torque presetting ring
14 | English
(4) Gear selector switch
(5) Belt clip
(6) Rechargeable battery
(7) Battery release button
(8) Worklight (LED)
(9) Rotational direction switch
(10) On/off switch
(11) Handle (insulated gripping surface)

Technical Data

English
Cordless Drill/Driver
Article number
Rated voltage
No-load speed A)
– First gear
– Second gear
Max. torque, hard/soft
screwdriving application
B)
according to ISO 5393
Max. drilling diameter (1st/2nd gear)
– Wood
– Steel
Chuck capacity
Max. screw diameter
Weight according to
EPTA-Procedure
01:2014 B)
Recommended ambient
temperature during
charging
Permitted ambient tem-
perature during opera-
C)
tion and during stor-
age
Recommended re-
chargeable batteries
Recommended char-
gers
A) measured at 20 - 25 °C with battery BBPB 18V 2.0 Ah.
B) Depends on battery in use
C) Limited performance at temperatures <0 °C

Noise/vibration information

Noise emission values determined according to
EN 62841-2-1.
Typically, the A-weighted sound pressure level of
the power tool is 72.5 dB(A). Uncertainty K=5 dB.
The noise level when working can exceed the
volume stated. Wear hearing protection!
Vibration total values a (triax vector sum) and un-
h
certainty K determined according to
BACSDB-1 18V
409010
V= 18
-1
min 0–460
-1
min 0–1800
Nm 55/28
mm 35
mm 13
mm 1.5–13
mm 10
kg 1.4–2.4
°C 0 to +35
°C –20 to +50
BBPB 18V X.X
Ah
BACB 18V
English
1 609 92A 5NK • 9.4.20