Additional Safety And Working Instructions - Berner BACIW BL CO-1 1/2 18V Notice Originale

TECHNICAL DATA CORDLESS IMPACT SCREWDRIVER
Production code....................................................................
No-load speed .................................................
Impact range ...................................................
Torque .............................................................
No-load speed .................................................
Impact range ...................................................
Torque .............................................................
No-load speed .................................................
Impact range ...................................................
Torque .............................................................
No-load speed .................................................
Impact range ...................................................
Torque .............................................................
Torque max. ..........................................................................
Max. diameter bolt / nut ........................................................
Tool reception .......................................................................
Battery voltage......................................................................
Weight according EPTA-Procedure 01/2014 (Li-Ion 2.0 Ah...12.0 Ah) .
Recommended ambient operating temperature ...................
Recommended battery types................................................
Recommended charger ........................................................
Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) .....................
Sound power level (Uncertainty K=3dB(A)) ..........................
Wear ear protectors!
Total vibration values (vector sum in the three axes)
determined according to EN 62841.
Vibration emission value a
Impact tightening of fasteners of the maximum capacity of the tool .
Uncertainty K= ...................................................................
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized
test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of
exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for
diff erent applications, with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may
signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is
switched off or when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the
total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the
tool and the accessories, keep the hands warm, organization of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifi cations provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
IMPACT SCREWDRIVER SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces,
when performing an operation where the fastener may
contact hidden wiring. Fasteners contacting a „live" wire
may make exposed metal parts of the power tool „live" and
could give the operator an electric shock.
Wear ear protectors. Exposure to noise can cause
hearing loss.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS

Use protective equipment. Always wear safety glasses
when working with the machine. The use of protective
clothing is recommended, such as dust mask, protective
gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust
protection mask.
457 763 - Berner-BACIW BL CO.indd 17 457 763 - Berner-BACIW BL CO.indd 17
h
BACIW BL CO-1 1/2" 18V BACIW BL CO-1 1/2" 18V
BACIW BL CO-1 1/2" 18V 01 000001-999999 BACIW BL CO-1 1/2" 18V 01 000001-999999
......................0-900 min ......................0-900 min -1 -1
....................0-1000 min ....................0-1000 min
-1 -1
......................0-102 Nm ......................0-102 Nm
....................0-1650 min ....................0-1650 min -1 -1
....................0-2400 min ....................0-2400 min
-1 -1
......................0-203 Nm ......................0-203 Nm
....................0-2400 min ....................0-2400 min
-1 -1
....................0-3500 min ....................0-3500 min
-1 -1
......................0-339 Nm ......................0-339 Nm
....................0-1200 min ....................0-1200 min
-1 -1
..............................- ..............................-
...........................34 Nm ...........................34 Nm
.........................339 Nm .........................339 Nm
........................M18 ........................M18
............... 1/2" (12,7 mm) ............... 1/2" (12,7 mm)
...........................18 V ...........................18 V
................1,5 ... 2,6 kg ................1,5 ... 2,6 kg
...................... -18...+50 °C ...................... -18...+50 °C
............ BBP18V-X, BBPP18V-X ............ BBP18V-X, BBPP18V-X
BBC14,4-18V, BBC-2 14,4V, BBCF 14,4V-18V BBC14,4-18V, BBC-2 14,4V, BBCF 14,4V-18V
......................99,79 dB (A) ......................99,79 dB (A)
.................... 110,79 dB (A) .................... 110,79 dB (A)
......................17,24 m/s ......................17,24 m/s
2 2
..........................1,5 m/s ..........................1,5 m/s 2 2
Do not machine any materials that present a danger to
health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls!
Do not switch the device on again while the insertion tool is
stalled, as doing so could trigger a sudden recoil with a
high reactive force. Determine why the insertion tool stalled
and rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the
machine is running.
When working in walls ceiling, or fl oor, take care to avoid
electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
17 ENGLISH
17.05.2021 11:12:37 17.05.2021 11:12:37