SOLIS BARISTA TRIPLE HEAT 1011 Mode D'emploi page 76

C LEA N I NG THE FIL T ER INS E RTS A N D P O R T A F I LT E R
■ ▲
The filter inserts and portafilter should be emptied out and rinsed under hot, running
water after every use to remove all residues of coffee oil. Turn the portafilter with an
empty filter insert into the brewing head and let hot water run through it by keeping
the button pressed for 30 seconds.
Should the holes in the filter inserts be clogged, dissolve a SOLITABS cleaning tablet
in a glass of hot water and place the filter inserts and the portafilter in the solution
for approx. 20 minutes. After that, carefully rinse the filter inserts and the porta-
filter under hot water and dry everything. The fine holes in the filter inserts can be
punched out resp. cleaned with the fine needle under the protection cap on the
cleaning tool.
CLE A N I NG T H E BRE WIN G HE A D
■ ▲
The brewing head with the brewing head sieve should be cleaned daily with a damp
cloth to wipe away all coffee powder residues. We recommend letting hot water run
through the brewing group regularly with the portafilter and an empty filter insert
mounted into the brewing head. Best press the
to let hot water run through at high pressure (see page 132, "Rinsing the brewing
group").
BAC K FL U SHING W IT H CLE A R W A TE R
■ ▲
1. Place the rubber cover in the filter insert for 1 cup. Place the filter insert in the
portafilter and mount the portafilter to the brewing group.
2. Press the button to build up pressure in the filter insert.
3. Repeat this process multiple times to remove all coffee oil residues in the appliance
resp. the espresso water ducts from the filter insert and the portafilter.
CLEANING THE OUTER HOUSING AND CUP WARMING PLATE
■ ▲
Before cleaning the outer housing, the appliance must be switched off and un-
plugged.
Wipe the outer housing and the cup warming plate clean with a soft, slightly wet
cloth and then dry it with a dry cloth.
Do not use abrasive cleaners, pads or cloths which can scratch the surface.
150
or button for 30 seconds
CL E ANI NG TH E DR I P TR AY
■ ▲
Before cleaning the drip tray, the appliance must be switched off and un-
plugged.
The drip tray should be removed, emptied and cleaned at regular intervals, particu-
larly when the drip tray full indicator is showing EMPTY ME!
Remove the drip tray grill from the tray. Clean the drip tray and the grill with warm
dish water. Do not use any aggressive detergents or scratching sponges. Rinse the
tray and the grill with clear water and dry everything carefully.
Caution: None of the espresso machine parts can be cleaned in the dish
washer!
Place the drip tray back in the appliance and place the grill back on the drip tray.
CL E ANI NG TH E AC C E S SO R Y C OM P AR T ME NT
■ ▲
The accessory compartment located behind the drip tray can be removed when the
drip tray has been removed. Clean the accessory compartment with warm dish wa-
ter and do not use any aggressive cleaners or scouring sponges. After that, dry the
accessory compartment thoroughly before replacing it.
Warning: Always when cleaning keep in mind that neither the power cord
nor the power plug or the appliance itself must be submerged in water or
other liquids.
Caution: None of the espresso machine parts can be cleaned in the dish
washer!
ST OR ING T HE S OLI S B AR I S TA T R I P LE HE AT
■ ▲
Set the steam lever and the hot water dial to the CLOSED position and switch the
appliance off with the POWER button. Disconnect the power plug from the power
socket. Store all accessory parts away.
Store the cooled down, cleaned, emptied and completely dry machine in an upright
position, best in the original packaging. Do not place any items on the appliance.
151