Technical Data - S+S Regeltechnik THERMASGARD RTF PLT Série Notice D'instruction

G
®
THERMASGARD
Room temperature sensor THERMASGARD
installation on vertically or horizontally installed in-wall flush boxes, with predetermined breaking point for on-wall cable entry.
This residential room temperature sensor is used to detect ⁄ display temperatures in closed dry rooms, in apartments, in cinemas, supermarkets,
storage rooms, office and business facilities.

TECHNICAL DATA:

Measuring ranges: .................... - 30 ...+70 °C (passive sensors) and
Sensor: .................................... types see table
Testing current: ...........................ca. 1 mA
Potentiometers: ........................ standard 1kΩ, max. 0.1 W
Turn switch: .............................. max. 24 V AC ⁄ DC, max. 130 mA,
Rocker switch: .......................... max. 24 V AC ⁄ DC, max. 130 mA
Pushbuttons: ............................ normally open contact, max. 24 V DC, max. 10 mA
LEDs: ....................................... max. 24 V DC (optional max. 24 V AC),
Enclosure: ................................ plastic, ABS, pure white (similar RAL 9010)
Dimensions: .............................. 85 x 91 x 27 mm (Frija I)
Installation: ............................... wall mounting or on in-wall flush box Ø 55 mm, base with 4-hole for mounting on vertically or
Electrical connection: ................ 0.14 - 1.5 mm² via terminal screws, on safety extra-low voltage max. 24 V DC only
Humidity: .................................. max. 90 % r. H., non-precipitating air
Protection class: ....................... III (according to EN 60 730)
Protection type: ........................ IP 30 (according to EN 60 529)
Lettering: ................................. standard is swelling arrow with center position, unfilled
Type ⁄ WG1
RTF xx
RTF PT100 ...*
RTF PT1000 ...*
RTF NI1000 ...*
RTF NI1000TK5000 ...*
RTF LM235Z ...*
RTF NTC1,8K ...*
RTF NTC10K ...*
RTF NTC10KPRECON ...*
RTF NTC20K ...*
RTF KTY81-210 ...*
RTF - U xx
RTF-U PT1000 ...*
RTF - UU P
RTM-U P
RTM-U U P_DISPLAY
...* = Version
RTF xx (diverse versions)
® RTF xx in an elegant enclosure made of plastic, with snap-on lid, base with 4-hole attachment for
0 ...+50 °C (at U-variant)
other ratings optional on request, e. g. 100 Ω, 2.5 kΩ, 5 kΩ, 10 kΩ,
(optional potentiometer 0...10 V, linear), with angle of rotation limiter
max. 5 steps (0, Auto, I, II, III), with angle of rotation limiter
standard green (optional red, yellow, or two-colour)
98 x 106 x 32 mm (Frija II)
horizontally installed in-wall flush boxes for cable entry from the back, with predetermined breaking
point for on-wall cable entry from top ⁄ bottom in case of plain on-wall installation
(optional special printing)
Sensor ⁄ Output
passive
Pt100 (according to DIN EN 60751, class B)
Pt1000 (according to DIN EN 60751, class B)
Ni1000 (according to DIN EN 43760, class B, TCR = 6180 ppm ⁄ K)
Ni1000 TK5000 (TCR = 5000 ppm ⁄ K), LG - Ni1000
LM235Z (TCR = 10 mV ⁄ K; 2.73 V at O °C), KP10
NTC 1,8 K
NTC 10K
NTC 10K Precon
NTC 20K
KTY 81-210
passive ⁄ active
Pt1000 / 0 - 10 V (potentiometer)
aktive
0 - 10 V (temperature and potentiometer)
0 - 10 V (temperature and potentiometer)
RTF xx T Version with sensor
and pushbutton (max. 24 V DC, max. 10 mA)
RTF xx LT Version with sensor,
LED (green), and pushbutton (max. 24 V DC, max. 10 mA)
RTF xx PT Version with sensor, potentiometer (1 kOhm, max. 0.1 W),
and pushbutton (max. 24 V DC, max. 10 mA)
RTF xx PLT Version with sensor, potentiometer (1 kOhm, max. 0.1 W),
LED (green), and pushbutton (max. 24 V DC, max. 10 mA)
RTF xx PW Version with sensor, potentiometer (1 kOhm, max. 0.1 W),
and rocker switch (max. 24 V AC/DC, max. 130 mA)
RTF xx PD Version with sensor, potentiometer (1 kOhm, max. 0.1 W),
and turn switch (max. 24 V AC/DC, max. 130 mA)
RTF xx P Version with sensor and potentiometer (1 kOhm, max. 0.1 W)
10
IP 30 (– 30...+ 70 °C)
IP 30 (0...+ 50 °C)
Display IP 30 (0...+ 50 °C)
■