Safety Rules - Haussmann 58485004 Manuel De L'utilisateur

Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
WARNING
Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals
known to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area and work with approved safety equipment. Always wear OSHA/NIOSH
approved, properly fitting face mask or respirator when using such tools.
WARNING
For your own safety, read all of the rules and precautions before operating tool.
WARNING
Always follow proper operating procedures as defined in this manual even if you are familiar with use of this or similar
tools. Remember that being careless for even a fraction of a second can result in severe personal injury.
Motor . . . . . 2/5 HP, 120V, 2.6 amps, 60 hz., Single Phase
Spindle diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2"
Drum diameters . . . . . . . . . . 1/2", 3/4", 1", 1-1/2", 2" and 3"
(12.7; 19; 25.4; 38.1; 50.8 and 76.2 mm)
Drum length . . . . . . . . . . . . . . . . . . . . . . . .4-1/2" (114 mm)
Spindle stroke . . . . . . . . . . . . . . . . . . . . . . . . 1" (25.4 mm)
Spindle oscillation . . . . . . . . . . . . . . . . . . . . . . . . . 30 SPM
TABLE OF CONTENTS
SAFETY RULES
SPECIFICATIONS
13
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Parts Illustration and List . . . . . . . . . . . . . . . . . . . . . 21-22
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Spindle speed . . . . . . . . . . . . . . . . . . . . . . . . . . 1725 RPM
Table diameter . . . . . . . . . . . . . . . . . . . . . . . .18" (457 mm)
Table height . . . . . . . . . . . . . . . . . . . . . . .15-1/2" (393 mm)
Dust port diameter . . . . . . . . . . . . . . . . . . . . . 2" (50.8 mm)
Base dimensions . . . . . . 22-1/2" x 16-1/2" (572 x 419 mm)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 lbs
(24 kg)