Standard Accessories; Applications - HIKOKI WH 10DL Mode D'emploi

Visseuse percussion à batterie
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 14

STANDARD ACCESSORIES

In addition to the main unit (1), the package contains the
accessories listed on page 75.
Standard accessories are subject to change without notice.

APPLICATIONS

○ Driving and removing of machine screws, wood screws,
tapping screws, etc.
SPECIFICATIONS
Model
No-load speed
Capacity (Ordinary bolt)
Tightening torque
(Maximum)
Rechargeable battery
Weight*
(According to EPTA-
Procedure 01/2014)
* Depending on attached battery. The heaviest weight is
measured with BCL1030 (sold separately).
Table 1
Before
charging
While
charging
Charging
Pilot lamp
complete
(red)
Overheat
standby
Charging
impossible
(2) Regarding the temperature of the rechargeable battery
The temperatures for rechargeable batteries are as
shown in the Table 2, and batteries that have become
hot should be cooled for a while before being recharged.
Table 2 Recharging ranges of batteries
Rechargeable batteries
BCL1015, BCL1030
WH10DL
0 – 2300 min
–1
M5 – M12
105 N·m
BCL1015: Li-ion DC 10.8 V
(1.5 Ah 3 cells)
1.0 – 1.1 kg
Indications of the pilot lamp
Lights for 0.5 seconds. Does not light
Blinks
for 0.5 seconds. (off for 0.5 seconds)
Lights continuously
Lights
Lights for 0.5 seconds. Does not light
Blinks
for 0.5 seconds. (off for 0.5 seconds)
Lights for 1 second. Does not light
for 0.5 seconds. (off for 0.5 seconds)
Blinks
Lights for 0.1 seconds. Does not light for
Flickers
0.1 seconds. (off for 0.1 seconds)
Temperatures at which the
battery can be recharged
0°C – 50°C
Model
Charging voltage
Weight
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger's power cord to the receptacle.
When connecting the plug of the charger to a receptacle,
the pilot lamp will blink in red (At 1-second intervals).
2. Insert the battery into the charger.
Firmly insert the battery into the charger till it contacts the
bottom of the charger as shown in Fig. 2.
3. Charging
When inserting a battery in the charger, the pilot lamp
will light up continuously in red.
When the battery becomes fully recharged, the
pilot lamp will blink in red (At 1-second intervals).
(See Table 1)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown in
Table 1, according to the condition of the charger or the
rechargeable battery.
Battery overheated.
Unable to charge.
(Charging will commence
when battery cools)
Malfunction in the battery
or the charger
(3) Regarding recharging time
Depending on the combination of the charger and
batteries, the charging time will become as shown in
Table 3.
Table 3 Charging time (At 20°C)
Charger
Battery
BCL1015
BCL1030
NOTE
The charging time may vary according to temperature
and power source voltage.
4. Disconnect the charger's power cord from the
receptacle.
5
English
UC10SL2
10.8 V
0.35 kg
Symbol mark
UC10SL2
Approx. 30 min.
Approx. 60 min.

Publicité

Table des Matières
loading

Table des Matières