Circuit Breaker - Ryobi GD200 Manuel D'utilisation

KNOW YOUR GARAGE DOOR OPENER
See Figures 3 - 5.
The safe use of this product requires an understanding of the
information on the product and in this operator's manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
AC RECEPTACLE
The garage door opener has two 120 Volt AC GFCI protected
receptacles with a combined rating of 10 Amps. These can
be used for operating AC garage door modules as well as
appropriate appliances, electrical lighting, and tools.
MODULE PORTS
Your garage door opener has seven ports for operating DC
garage door modules.
AUTOMATIC REVERSAL SYSTEM
When a closing garage door contacts an object that is
1-1/2 in. above the garage floor, the automatic reversal
system will stop and raise the door to the fully open position.
BATTERY BACKUP
When not connected to an AC power source, the garage
door opener and LED lights can be operated with RYOBI
18 Volt ONE+ lithium-ion batteries.
™
CAR REMOTES
Convenient car remotes allow you to activate the garage
door opener from a distance of up to 300 ft. The remotes
are equipped with a visor clip, so you can store them on
your car's sun visor.
BATTERY CHARGER
The built-in battery charger accepts RYOBI 18 Volt ONE+
lithium-ion batteries.
BELT DRIVE SYSTEM
This product is equipped with a belt drive system that is
quieter than traditional chain drive models.

CIRCUIT BREAKER

The circuit breaker is provided to protect the AC modules
against electrical overload. The circuit breaker may be reset
by pressing the circuit breaker reset button.
EMERGENCY RELEASE ROPE
In the case of an emergency or entrapment, pulling the
emergency release rope will allow you to manually raise a
closed garage door.
FEATURES
HOMELINK
Features on your garage door opener can be controlled by
cars and homes equipped with HomeLink
HomeLink
®
Gentex Corporation.
INDOOR KEYPAD
The indoor keypad is installed on the interior of the garage
and can be used to open and close the garage door, activate
the DC module ports, and turn the LED lights on and off.
LED LIGHTS
LED lights are located beneath the light cover and illuminate
whenever the motor is running, the LIGHT (
indoor keypad is pressed, or motion is detected. To turn the
LED lights off, press the LIGHT (
NOTE: By default, the LED lights will illuminate for three
minutes after the LIGHT (
can be adjusted in one minute increments, between three
and ten minutes, using the RYOBI Garage Door Opener
Module System App.
MOTION SENSING
Passive infrared motion sensing turns the LED lights on when
movement is detected in the garage.
NOTE: The motion sensor is deactivated for ten seconds
each time the LIGHT (
RAIL SYSTEM
The ergonomic rail design makes assembly and installation
quick and easy.
SMART PHONE COMPATIBILITY
The garage door opener can be operated remotely with a
smart phone using the RYOBI Garage Door Opener Module
™
System App. For more information, visit ryobitools.com or
download the app from the App Store or Google Play Store.
SAFETY SENSORS
Your garage door opener comes with two sensors that cast
an invisible light beam across the opening of your garage.
If an object crosses the path of the beam while the garage
door is closing, the door will automatically stop and reverse
to the fully open position.
VACATION MODE
To enter and exit vacation mode, press the LOCK ( ) button
on the indoor keypad. When in vacation mode, the garage
door opener can only be controlled by the indoor keypad
and smart phone app.
WIRELESS OUTDOOR KEYPAD
The wireless outdoor keypad can be used to open and close
the garage door. For security, the outdoor keypad allows you
to set up a custom four digit personal identification code.
12 - English
COMPATIBILITY
®
and the HomeLink house icon are registered trademarks of
®
) button is pressed. The time
) button is pressed.
control systems.
®
) button on the
) button.