Troubleshooting - Maytag MHW7000A Série Guide D'utilisation Et D'entretien

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.maytag.com/product_help – First try the solutions suggested here or visit our website at www.maytag.com/product_help –
If you experience If you experience
Error Code Appears in Display Error Code Appears in Display
Once any possible issues are corrected, touch POWER/CANCEL once to clear the code. Reselect and restart the cycle. Once any possible issues are corrected, touch POWER/CANCEL once to clear the code. Reselect and restart the cycle.
Sud Sud
(Excess suds) (Excess suds)
appears in display appears in display
F F 08 F 08 E E 01 E 01
followed by followed by
(water supply error) (water supply error)
appears in display appears in display
F F 09 F 09 E E 01 E 01
followed by followed by
(drain pump system (drain pump system
error) appears in display error) appears in display
F 05 F F 05 E 02 E 02 E
followed by followed by
(door will not lock) (door will not lock)
appears in display appears in display
F 07 F F 07 E 01 E 01 E
followed by followed by
(motor drive error) (motor drive error)
appears in display appears in display
"rL" "rL"
(remove load) (remove load)
appears in display appears in display
Washer making error Washer making error
beeps beeps
Washer beeps when Washer beeps when
START is touched START is touched
F F F ## E ## F ## E ## E E
code other code other
than as described above than as described above
appears in display appears in display
Int (interrupted) Int (interrupted)
appears in display appears in display
16
In Canada www.maytag.ca for assistance and to possibly avoid a service call. In Canada www.maytag.ca for assistance and to possibly avoid a service call.
Possible Causes Possible Causes
Excessive suds in washer. Washer is Excessive suds in washer. Washer is
running a suds reduction routine. running a suds reduction routine.
Check for proper water supply. Check for proper water supply.
Check plumbing for correct drain Check plumbing for correct drain
hose installation. Drain hose extends into hose installation. Drain hose extends into
standpipe farther than 4 standpipe farther than 4 1 1 1 ⁄ ⁄ ⁄ " (114 mm). ⁄ " (114 mm).
2 2
Not using HE detergent or using too Not using HE detergent or using too
much HE detergent. much HE detergent.
Washer door not locking. Washer door not locking.
Motor is having difficulty turning Motor is having difficulty turning
the drum. the drum.
Load detected in drum during Clean Load detected in drum during Clean
® ®
Washer with affresh Washer with affresh cycle. cycle.
Door has not been opened and closed Door has not been opened and closed
for at least 3 cycles. for at least 3 cycles.
Door not closed. Door not closed.
System error code. System error code.
The cycle was paused or cancelled. The cycle was paused or cancelled.
Allow the washer to continue. Use only HE detergent. Allow the washer to continue. Use only HE detergent.
Always measure detergent, and base detergent quantity on Always measure detergent, and base detergent quantity on
load size. Follow detergent manufacturer's instructions. load size. Follow detergent manufacturer's instructions.
Both hoses must be attached and have water flowing to the inlet Both hoses must be attached and have water flowing to the inlet
valve. valve.
Both hot and cold water faucets must be on. Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged. Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose. Remove any kinks in the inlet hose.
Touch POWER/CANCEL once to clear the code. Then touch Touch POWER/CANCEL once to clear the code. Then touch
POWER/CANCEL again to restart washer. If code appears again, POWER/CANCEL again to restart washer. If code appears again,
call for service. call for service.
Check drain hose for proper installation. Check drain hose for proper installation.
Make sure the drain hose is not kinked, pinched, or blocked. Make sure the drain hose is not kinked, pinched, or blocked.
Remove any clogs from drain hose. Remove any clogs from drain hose.
Use drain hose form and securely attach to drainpipe or tub. Use drain hose form and securely attach to drainpipe or tub.
Lower drain hose if the end is higher than 96" (2.4 m) above Lower drain hose if the end is higher than 96" (2.4 m) above
the floor. the floor.
Use only HE detergent. Always measure detergent and follow Use only HE detergent. Always measure detergent and follow
manufacturer's directions based on load size and soil level. manufacturer's directions based on load size and soil level.
Touch POWER/CANCEL to cancel the cycle. Make sure the door Touch POWER/CANCEL to cancel the cycle. Make sure the door
is closed completely and latching. Check for items in the washer is closed completely and latching. Check for items in the washer
drum that may be keeping the door from closing completely. drum that may be keeping the door from closing completely.
Washer is tightly packed. Remove some items. See "Cycle Guide" Washer is tightly packed. Remove some items. See "Cycle Guide"
for load size recommendations. Make sure that all shipping for load size recommendations. Make sure that all shipping
materials have been removed. See the Installation Instructions. materials have been removed. See the Installation Instructions.
Remove items from washer drum and restart Clean Washer with Remove items from washer drum and restart Clean Washer with
affresh affresh ® ® cycle. cycle.
This code may appear when the washer is first turned on. This code may appear when the washer is first turned on.
Open and close the door to clear the display. Open and close the door to clear the display.
Close the door completely. Close the door completely.
Touch POWER/CANCEL once to clear the code. Then touch Touch POWER/CANCEL once to clear the code. Then touch
POWER/CANCEL again to restart washer. If code appears again, POWER/CANCEL again to restart washer. If code appears again,
call for service. call for service.
The washer can take 20 to 30 minutes to stop spinning and drain The washer can take 20 to 30 minutes to stop spinning and drain
and will display this error code during that time. Touch POWER/ and will display this error code during that time. Touch POWER/
CANCEL once to clear the code. Then touch POWER/CANCEL CANCEL once to clear the code. Then touch POWER/CANCEL
again to restart washer. again to restart washer.
Solution Solution