Husqvarna 325L Manuel D'utilisation page 14

4. Make sure that the air filter is not clogged.
5. Make sure that the safety devices on the product is
not defective.
6. Make sure that the product has no fuel leaks.
To start a cold engine
1. Push the air purge bulb 10 times. (Fig. 27)
2. Pull the choke control up. (Fig. 28)
3. Hold the body of the product on the ground with your
left hand. (Fig. 29) Do not step on the product. Pull
the starter rope handle slowly until you feel some
resistance. Then pull the starter rope handle with
force.
Note: Do not pull the throttle trigger while you start
the engine.
4. Continue to pull the starter rope handle until the
engine starts or tries to start (max. 3 pulls). If the
engine starts or tries to start, push the choke control
down. Continue to pull until the engine starts. Wait
60 seconds after a start before you pull the throttle
trigger.
CAUTION: Do not pull the starter rope
until it stops. Do not let go of the starter
rope when it is fully extended. Release
the starter rope slowly. Failure to obey
these instructions can cause damage to
the engine.
To start a warm engine
1. Push the air purge bulb 10 times.
2. Pull the starter rope until the engine starts.
To start the engine when the fuel is too hot
If the product does not start, the fuel can be too hot.
Note: Always use new fuel and decrease the operation
time during warm weather.
1. Put the product in a cool area away from open
sunlight.
2. Let the product cool down for 20 minutes at
minimum.
3. Press the air purge bulb again and again for 10-15
seconds.
4. Obey the procedure to start a cold engine. Refer to
To start a cold engine on page 14 .
To stop
• Push the stop switch to stop the engine. (Fig. 30)
Note: The stop switch automatically goes back to its
initial position.
14
To operate the grass trimmer
CAUTION: Make sure that you slow the
engine to idle speed after each operation. A
long period at full throttle without a load on
the engine can cause damage to the engine.
Note: Clean the cover of the trimmer head when you
attach a new trimmer line to prevent vibrations. Examine
other parts of the trimmer head and clean if it is
necessary.
To trim the grass
1. Hold the trimmer head immediately above the
ground at an angle. Do not push the trimmer line into
the grass. (Fig. 31)
2. Decrease the length of the trimmer line by 10-12
cm / 4-4.75 in.
3. Decrease the engine speed to decrease the risk of
damage to plants.
4. Use 80 % throttle when you cut grass near objects.
(Fig. 32)
To cut the grass
1. Make sure that the grass trimmer line is parallel to
the ground when you cut. (Fig. 33)
2. Do not push the trimmer head to the ground. The
ground and the product can be damaged.
3. Do not let the trimmer head touch the ground
continuously, it can cause damage to the trimmer
head.
4. Use full throttle when you move the product from
side to side to cut grass. Make sure that the grass
trimmer line is parallel to the ground. (Fig. 34)
Grass trimmer head
• Make sure that you wind the grass trimmer line
tightly and equally around the drum to decrease the
vibration.
• Use only the approved grass trimmer heads and
grass trimmer lines. See
• Use a correct length of the grass trimmer line. A long
grass trimmer line uses more engine power than a
short grass trimmer line.
• Make sure that the cutter on the cutting attachment
guard is not damaged.
• Soak the grass trimmer line in water for 2 days
before you attach the grass trimmer line to the
product. This increases the life of the grass trimmer
line.
To replace the trimmer line
(Fig. 35)
(Fig. 36)
(Fig. 37)
(Fig. 38)
(Fig. 39)
Accessories on page 18 .
882 - 001 - 10.10.2018