Euro-Pro Operating Shark PLUS EP703 Manuel D'utilisation page 4

OPERATING INSTRUCTIONS
4. Tilt the bag forward as shown in
Fig. 7.
Fig. 7
5. Lock the bag in its place with the lock
as shown in Fig. 8.
Bag
Lock
Fig. 8
6. Close the top cover of the vacuum.
Note: The vacuum cleaner cover will not
close if there is no cloth or paper bag
inserted and locked in its place in the bag
holder
Using the Accessories
The dusting brush and crevice tool can
be used with both the flexible hose
alone, or attached to the end of one or
both of the extension tubes, for greater
reach.
Using the Floor-to-Carpet Brush
Please note that the convenient 3-way
adjustability and 6 soft rubber wheels
on the floor-to-carpet brush enable
you to freely move from carpet to bare
floor without any adjustments.
Suggestion: After vacuuming with the
floor-to-carpet brush, use the crevice
tool to clean the floor brush.
Dusting Brush
The dusting brush is used for
the furniture
Crevice Tool
For radiators, crevices, corners,
baseboards and between cushions.
Accessory Caddy
Located on the extension tube, the
accessory caddy allows you to store
your accessories within your reach. No
more hunting for the dusting brush or
crevice tool, the accessory caddy keeps
your vacuum accessories at your
fingertips. (Fig. 9)
Fig. 9
Using the Air Driven Turbo Brush
The air driven turbo brush may be used
with the extension tubes or with the
flexible hose only.
To use the air driven turbo brush with the
extension tubes:
1. Attach the air driven turbo brush
to the end of the extension tube.
You may wish to use only one
extension tube, or you may use both
tubes for greater reach.
2. To remove the turbo brush, pull and
twist it off of the extension tube.
To use the air driven turbo brush with the
flexible hose only:
1. Remove the extension tubes from the
end of the flexible hose.
2. Attach the air driven turbo brush to
the end of the flexible hose.
3. To remove, pull and twist the brush
off of the end of the flexible hose.
The efficiency of your air driven turbo
brush depends on the bristle brush
rotating at high speed. Strong air
suction is needed to accomplish this.
In order to ensure that maximum air
suction is maintained, please read the
following instructions:
1. Change the dust bag frequently.
2. Replace the pre-motor and post
motor filters as needed..
3. Ensure that the rotating brush is
kept free of hair and string which
may accumulate and decrease
brush performance.
4. Keep Air Driven Turbo Brush
turbine free of dirt and foreign
matter. (See Fig. 9 and cleaning
instructions)
5
OPERATING INSTRUCTIONS
Cleaning Air Driven Turbo Brush
Tilt
Upwards
Locking
Latch
Turbine
Wheel
Fig. 10
From time to time, the turbine of your
turbo brush will require cleaning. To do
this:
1. Remove the turbo brush from the hose
or unit.
2. Turn turbo brush over and open the
hinged cover to access the turbine
wheel. (Fig. 10)
3. There may be some dust, lint, hair, etc
on the turbine wheel. Remove as much
of this as possible.
4. You may also use the unit's hose to
remove any additional debris from the
turbine.
Manual Suction Control
Your vacuum cleaner includes a manual
variable suction control. The suction
power can be adjusted by moving the
slide regulator to the desired position.
(Fig. 11) Open gives you less suction,
closed gives you maximum suction. For
example, less suction is required on
upholstery and draperies compared to
thick carpets, which require maximum
suction.
Slide Regulator
Fig. 11
Using your Vacuum
Once all attachments are in place,
unwind a sufficient length of cable and
insert the plug into the wall outlet.
(Fig. 12)
1. Insert the power plug into an electrical
outlet.
Fig. 12
2. Press the Power On/Off button to turn
the vacuum cleaner "On". (Fig. 13)
3. To rewind the power cord, press the
cord rewind button with one hand and
hold the plug of the power cord with
the other hand to ensure that it does
not whip causing damage or injury.
(Fig. 13)
Fig. 13
Power Cord
Your vacuum cleaner includes a power
cord, which is automatically retractable.
To extend your power cord:
• Pull from the rear and extend to
desired length.
• A yellow mark on the power cord
shows the ideal cable length.
Caution
: DO NOT pull the power cord
beyond the red mark on the cord as
doing so will damage the cord.
To rewind the power cord:
• Press the power button and
disconnect plug from electrical outlet.
Then press on the cord rewind button.
(Fig. 13)
• If the cord does not fully retract, pull it
out again and then press on cord
rewind button.
Warning
: Hold the plug when rewinding
the cord. DO NOT allow cord to whip
when rewinding.
6
Cord
Rewind
Button
On/Off
Button