Boutside Back Exhaust; Outside Back Exhaust; Remove Blower Plate; Attach Mounting Plate To Wall - Frigidaire Gallery Série Instructions D'installation

OUTSIDE BACK EXHAUST

B
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B2. Remove Blower Plate
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
IMPORTANT NOTES:
•
Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•
Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
PREPARING THE REAR WALL
B1.
FOR OUTSIDE BACK EXHAUST
You need to cut an opening in the rear wall for
outside exhaust.
NOT E:
IT IS VERY
READ AND FOLL IMPO RTAN
IN THE
INST ALLA OW THE T TO
BEFO RE PRO TION INST DIRE CTIO
REAR CEED RUC TION NS
WAL L ING WITH S
This Rear TEM PLAT THIS
mounti Wall Templa E. 3/8" TO EDGE
outlet. ng plate and to te serves 12"
locate the to positio n the bottom
1. Use a level horizon tal exhaus
accura tely. to check that the t
2. Locate templa
right side and mark at least te is positio ned
  of the centerl one stud 4"   
I t is importa ine. on the left or
screw mounte nt to use     
of the microw d firmly in a stud at least one wood   
locatio ns ave. Mark to suppor   
3. Drill for the supplie two additio t the weight   
holes in the marked d toggle nal, evenly spaced   
a stud, drill a 3/16" locatio ns. bolts.
that do not line hole for Where 
toggle bolts. up with wood screws there is 
  a stud, drill 5/8" . For holes  
AT THIS D O NOT holes for 
TIME. INSTA LL THE MOUN  
4. Remov e the templa TING PLATE   
5. Review te from
installa the Installa tion Instruc the rear 
tion situatio tion book wall.
n. for your
Darle vuelta
versió n a la hoja
en Españ para consu
ol. ltar la
 
Loca te and mark  
moun ting   
plate . holes to align with      
IMPO RTAN        
T: holes in the       
LOCA  
TE AT LEAS T   
THE CEN ONE STUD   
TERL INE.  
MAR K THE LOCA ON EITH     
SPAC ER SIDE 
ED TOG TION FOR OF
AREA GLE BOLT 2 ADD ITION AL,
. S IN THE
MOU NTIN EVEN LY     
G PLAT
E
    

Trim the
rear wall
temp late
along the dotte
d line.

 Loca te
and mark
moun ting holes to
plate .
IMPO RTAN
LOCA T:
TE AT
THE CEN LEAS T
TERL INE.
MAR K
THE LOCA
SPAC ED TOG
 AREA GLE BOLT
.

•
Read the instructions on the REAR
WALL TEMPLATE.
•
Tape it to the rear wall.
•
Cut the opening, following the instructions of the
REAR WALL TEMPLATE.
Installation Instructions
NOTE: IT IS VERY IMPORTANT
READ AND FOLLOW
IN THE INSTALLATION
BEFORE PROCEEDING
REAR WALL TEMPLATE.
This Rear Wall Template
mounting plate and to locate
outlet.
1. Use a level to check
accurately.
2. Locate and mark at least
right side of the centerline.
It is important to use at
screw mounted firmly in
of the microwave. Mark
locations for the supplied
3. Drill holes in the marked
a stud, drill a 3/16" hole
that do not line up with
toggle bolts.
DO NOT INSTALL THE
AT THIS TIME.
4. Remove the template
5. Review the Installation
installation situation.
Darle vuelta a la hoja
versión en Español.
Locate and mark holes
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE
THE CENTERLINE.
MARK THE LOCATION
SPACED TOGGLE BOLTS
AREA.
Trim the rear wall template
Trim the
rear wall
temp late
along
the dotte
d line.
align with
holes in
the
ONE STUD
ON EITH
ER SIDE
TION FOR OF
2 ADD
S IN THE ITION AL,
EVEN
MOU NTIN LY
G PLAT
E

(Horizontal Duct)
3/8" TO EDGE
along the dotted line.
Trim the rear wall template
12"
TO
THE DIRECTIONS
INSTRUCTION S
WITH THIS
serves to position the bottom 4"
the horizontal exhaust
that the template is positioned
one stud on the left or
least one wood
a stud to support the weight
two additional, evenly spaced
toggle bolts.
locations. Where there is
for wood screws. For holes
a stud, drill 5/8" holes for
MOUNTING PLATE
from the rear wall.
Instruction book for your
para consultar la
to align with holes in the
STUD ON EITHER SIDE OF
EVENLY
FOR 2 ADDITIONAL,
IN THE MOUNTING PLATE
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT: STUD ON EITHER SIDE OF
LOCATE AT LEAST ONE
THE CENTERLINE. EVENLY
FOR 2 ADDITIONAL,
MARK THE LOCATION IN THE MOUNTING PLATE
along the dotted line. SPACED TOGGLE BOLTS
AREA.

REMOVE BLOWER PLATE

B2.
Remove and save the screw that holds the blower
plate to the microwave. Lift off the blower plate.
Blower Plate
EN-16
IMPORTANT :Do not remove the cardboard
spacers b etween the heat shield and door.
Back of
Microwave