Connection And Assembly; Safety Precautions; Warranty Terms - Melitta M600 Mode D'emploi

10.Connection and Assembly

All MELITTA appliances are supplied ready for connecting.
Before installation, however, the on-site water and electricity
supplies should be made easily accessible within a radius of
one metre from the machine.
These preparations must be carried out by authorized special-
ists in accordance with national regulations. The MELITTA
Customer Service Department is not authorized to undertake
such work and cannot accept responsibility for the installation.
The machine must be placed on a solid table top. If the
connections are to be made from under the table top, an
opening of approx. 100 mm. Ø must be provided in the cen-
tre below the coffee machine to allow access to the mains
supplies. The cables and pipes supplied can be led from the
hot water unit under the base unit and directly through the
table top opening.
b.
C.
mini. 600
a) Electric supply
The distribution voltage must conform with the data indicated
on the type plate. The mains lead must be fuse-protected
separately by the client. The connection should be made by
means of a plug socket secured by a residual current opera-
ted device (max. 30 mA). Should a fixed connection be
necessary, a switch with at least 3 mm contact break must
be provided directly next to the machine for an all-pole mains
cut-off.
b) Water supply
A stop valve with backflow suppressor, according to specifi-
cations, is to be installed within easy access. If a water filter
is used, this must be mounted vertically. For safety reasons,
the special connecting hoses supplied with the machine may
not be shortened during assembly. The static water supply
pressure must be at least 2 bar. Should the pressure exceed
6 bar, a pressure reducing valve must be inserted between
the machine and the main stop valve.
Before operating the machine for the first time, the water fil-
ter must be activated with at least 10 litres of water at full
flow. This process must be repeated for every new filter car-
tridge.
c) Water outlet
All machines are provided with water outlet muffs and should
be connected with the hoses supplied to a drain pipe with
stench trap.
Assembly
Should the machine be used as a filter coffee unit (FKA), the
wall bracket for the hot water unit is to be attached to the wall
Operating instructions - pages 7 - 12
a.
according to the assembly drawing supplied.
With the screws, washers and tapped bushes provided, the
hot water unit can be attached to the base unit, wall bracket
or directly to a table surface.
Swivel arm
With the swivel arm (8) pointing forward, attach it to the
opening in the lid of the hot water unit and push downward
into place. It can now be turned to the left or right until it rea-
ches the stopping point.

11.Safety precautions

• Keep these operating instructions near the machine,
so that the operator can use the machine correctly at
all times.
• Maximum machine safety is among those product fea-
tures which MELITTA SystemService places particular
emphasis on.
Despite all safety precautions, however, incorrect
handling of any machine can always result in potential
risks. For this reason - in the interest of your own
safety - we have compiled the following list of danger
warnings.
• The machine must not be operated outdoors.
• The connection of the machine to the customer's
mains supply as well as all maintenance and repair
work must be carried out exclusively by the Technical
Service staff of MELITTA SystemService.
• Caution! There is a danger of scalding within the
area of the coffee outlet and hot water outlet.
• MELITTA SystemService will not be liable for damages
arising from lack of maintenance, unprofessional work
on the machine or the installation of parts not con-
forming with the original construction.
• MELITTA SystemService reserves the right to carry
out, at any time and without prior arrangement, any
modifications in the interest of technical progress.
• If the machine is to be out of operation for a longer
period it must first be cleaned thoroughly.
Turn off water and electricity supply at the mains (see
directions under „Switching the machine off", page 9).
• In case of freezing temperatures, the machine must be
drained of all water to prevent any damage. Please call
MELITTA Technical Service in this case.
• According to accident prevention regulation VBG 4 of
the German trade association, the operator is obliged
to have this electrical appliance tested for safety in
regular intervals by an authorized electrician. The time
interval between two inspections for this mounted devi-
ce is no more than 4 years. The appliance corre-
sponds to VBG 4, it need not therefore be tested furt-
her before its initial operation.
The prescribed inspection can, on request, be carried
out and confirmed by MELITTA Technical Service.

12.Warranty terms

We grant a twelve-month warranty for the proper functio-
ning of this appliance/installation. The warranty period com-
mences on the day of installation. During this period, any
defects arising from faulty materials, defective execution
and faulty construction will be repaired by us or by a com-
pany authorized by us, free of charge, subject to proper use
GB
11