Accessories - Milwaukee M18 FUEL 2787-20 Manuel De L'utilisateur

To reduce the risk of in-
WARNING
jury, always keep hands,
gloves, rags, clothing, etc. away from
moving parts and chips. Do not try to
remove chips while the cutter is rotat-
ing. Chips are sharp and can pull objects into
moving parts.
8. Start the drill motor by pulling the
ON(I) / OFF(O) switch out, by
both sides, to the on(I) position.
The drill motor will not start if the
magnet icons are not aligned,
activating the magnet.
Excessive force
WARNING
on the feed handle
will break magnet free.
9. Even large bits only require a
small amount of pressure on the feed handle.
When feeding the cutter into the material, apply
only enough force to produce a curled chip. Apply-
ing too little force will result in small broken chips
and increased cutting time. Applying too much
force will cause overheating of the cutter resulting
in short cutter life. Overheating of the cutter can
be noticed when cutter and chips turn brown or
blue. Excessive force can cause the cutter to slow
down to a point where cutting time will increase.
The use of cutting lubricants will reduce cutting
heat and increase cutter life
Use less feed pressure when slotting or notching
because there is less support for the cutting edges
in these situations.
10. Keep constant pressure throughout the entire
operation to prevent chips and burrs from falling
under the cutting edges. Cutting debris under the
cutter can make cutting difficult or impossible.
11. When the cut is complete, withdraw the cutter
while the spindle is still rotating.
12. Stop the drill motor by pushing in the ON(I) / OFF(O)
switch.
13. When the spindle has stopped rotating, use a
pliers to remove cutting debris and chips from the
cutter and spindle. Use care to avoid damaging
the cutter teeth.
14. The center pin is spring loaded. Provide protection
from ejected slug for people and property below
cutting area.
15. Firmly grip the tool and rotate the magnet knob
to disengaging the magnet.
16. When drilling on pipe, use the accessory pipe
adaptor 48-10-0130 and the safety strap.
MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
To reduce the risk of personal in-
WARNING
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Clean dust and debris from
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
For repairs, return the tool, battery pack and charger
to the nearest authorized service center.

ACCESSORIES

Use only recommended accesso-
WARNING
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
SERVICE - UNITED STATES
1-800-SAWDUST
Monday-Friday, 7:00 AM - 6:30 PM CST
www.milwaukeetool.com
or visit
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: metproductsupport@milwaukeetool.com
B e c o m e a H e a v y D u t y C l u b M e m b e r a t
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
6
Cleaning
any vents. Keep
Repairs
(1.800.729.3878)
tool