Bevel Cut; Compound Mitre Cut - Rona 2001733 Manuel D'utilisation

OPERATING INSTRUCTIONS
17) Check that the blade guard operates
correctly and covers the blade as the saw
arm is lowered.
18) Connect the saw to the power supply and
run the blade to make certain that it is
operating correctly.
Cross cut
WARNING. When making any adjustment to
your work, ensure that the blade is stationary
and keep your hands away from the area of
the switch.
If possible, always use a clamping
device such as a 'G" clamp to secure
your workpiece.
When cutting your workpiece, keep your
hands well away from the blade area.
Do not remove a cut-off piece on the right-
hand side of the blade using your left hand.
A crosscut is made by cutting across the grain
of the workpiece. A 90º crosscut is made with
the Mitre table set at 0º. Mitre crosscuts are
made with the table set at some angle other
than zero.
1) Pull on the release knob (2) and lift the saw
arm (1) to its full height.
2) Loosen the Mitre locks (15).
3) Rotate the Mitre table (12) until the pointer
aligns with the desired angle.
4) Retighten the Mitre locks (15).
WARNING. Be sure to tighten the Mitre locks
before making a cut. Failure to do so could
result in the table moving during the cut and
cause serious personal injury.
5) Place the workpiece flat on the table with
one edge securely against the fence (11). If
the board is warped, place the convex side
against the fence (11). If the concave side is
placed against the fence, the board could
break and jam the blade.
GB
6) When cutting long pieces of timber, support
the opposite end of the timber with side
support bars, a roller stand or a work
surface that is level with the saw table.
7) Before turning on the saw, perform a dry run
of the cutting operation to check that there
26
are no problems such as a clamp interfering
with the cutting action.
8) Hold the operating handle (3) firmly and
squeeze the switch trigger (16). Allow the
blade to reach maximum speed and slowly
lower the blade into and through
the workpiece.
9) Release the switch trigger (16) and allow
the saw blade to stop rotating before
raising the blade out of the workpiece.
Wait until the blade stops before removing
the workpiece.

Bevel cut

WARNING. When making any adjustment to
your work, ensure that the blade is stationary
and keep your hands away from the area of
the switch.
If possible, always use a clamping device such
as a 'G" clamp to secure your workpiece.
When cutting your workpiece, keep your
hands well away from the blade area.
Do not remove a cut-off piece on the right-
hand side of the blade using your left hand.
A bevel cut is made by cutting across the
grain of the workpiece with the blade angled
to the fence and Mitre table. The Mitre table is
set at the zero degree position and the blade
set at an angle between 0º and 45º.
1) Pull on the release knob (2) and lift the saw
arm to its full height.
2) Loosen the Mitre locks (15).
3) Rotate the Mitre table (12) until the pointer
aligns with zero on the Mitre scale (13).
4) Retighten the Mitre locks (15).
WARNING. Be sure to tighten the Mitre locks
before making a cut. Failure to do so could
result in the table moving during the cut,
causing serious personal injury.
5) Loosen the bevel lock (7) and move the saw
arm(1) to the left to the desired bevel angle
(between0º and 45º). Tighten the
bevel lock (7).
6) Place the workpiece flat on the table with
one edge securely against the fence (11).
If the board is warped, place the convex
OPERATING INSTRUCTIONS
side against the fence. If the concave side
is placed against the fence, the board could
break and jam the blade.
7) When cutting long pieces of timber, support
the opposite end of the timber with side
support bars,a roller stand or a work surface
that is level with the saw table.
8) Before turning on the saw, perform a dry run
of the cutting operation to check that there
are no problems such as a clamp interfering
with the cutting action.
9) Hold the operating handle (3) firmly and
squeeze the switch trigger (16). Allow the
blade to reach maximum speed and slowly
lower the blade into and through
the workpiece.
10) Release the switch trigger (16) and allow
the saw blade to stop rotating before
raising the blade out of the workpiece.
Wait until the blade stops before removing
the workpiece.

Compound mitre cut

WARNING. When making any adjustment to
your work, ensure that the blade is stationary
and keep your hands away from the area of
the switch.
If possible, always use a clamping
device such as a 'G" clamp to secure
your workpiece.
When cutting your workpiece, keep your
hands well away from the blade area.
Do not remove a cut-off piece on the right-
hand side of the blade using your left hand.
A compound Mitre cut involves using a Mitre
angle and a bevel angle at the same time.
It is used in making picture frames, to cut
mouldings, making boxes with sloping sides
and for roof framing. Always make a test cut
on a piece of scrap wood before cutting into
the good material.
1) Pull on the release knob (2) and lift the saw
arm to its full height.
2) Loosen the Mitre locks (15).
3) Rotate the Mitre table (12) until the pointer
aligns with the desired angle on the Mitre
scale (13).
4) Retighten the Mitre locks (15).
WARNING. Be sure to tighten the Mitre lock
before making a cut. Failure to do so could
result in the table moving during the cut,
causing serious personal injury.
5) Loosen the bevel lock (7) and move the
saw arm (1) to the left to the desired bevel
angle (between 0º and 45º). Tighten the
bevel lock (7).
6) Place the workpiece flat on the table with
one edge securely against the fence (11).
If the board is warped, place the convex
side against the fence. If the concave side
is placed against the fence, the board could
break and jam the blade.
7) When cutting long pieces of timber, support
the opposite end of the timber with the
side support bars, a roller stand or a work
surface that is level with the saw table.
8) Before turning on the saw, perform a dry run
of the cutting operation to check that there
are no problems such as a clamp interfering
with the cutting action.
9) Hold the operating handle (3) and firmly
and squeeze the switch trigger (16). Allow
the blade to reach maximum speed and
slowly lower the blade into and through the
workpiece.
10) Release the switch trigger (16) and allow
the saw blade to stop rotating before
raising the blade out of the workpiece.
Wait until the blade stops before
removing the workpiece.
27
GB