Setting The Comfort Mode Temperature; Consumption Indication Accumulated In Kwh, Energy Savings; Child Anti-Tamper, Keypad Lock/Unlock; Day And Daily Programme Integrated, Energy Savings - RADSON Flores C E Notice D'utilisation

SETTING THE COMFORT MODE
TEMPERATURE
You can access the Comfort temperature set up from the Auto and
Comfort Mode. It is preset to 19°C.
Using and you can adjust the temperature from 7°C to 30°C by
intervals of 0.5° C.
auto auto
mode mode
Note: you can limit the Comfort temperature,
tails.
CONSUMPTION INDICATION
ACCUMULATED IN KWH, ENERGY
SAVINGS
It is possible to see the estimation of energy consumption in kWh since
the last reset of the energy meter.
Display of the estimated power consumption
To see this estimation, from Auto,
Comfort, Eco or Frost protection mode,
then press .
To exit the display mode of
consumption: press any button, the
device is automatically in the previous active mode.
Resetting the energy meter
To reset the energy meter, from Auto, Comfort, Eco or Frost protection
mode, then proceed as follows.
1- Press .
2- Press simultaneously and
To exit resetting the energy meter, press any button, the device is
automatically in the previous active mode.
CHILD ANTI-TAMPER,
KEYPAD LOCK/UNLOCK
Keypad lock
To lock the keypad, press the
and buttons and hold them
down for 10 seconds. The padlock
symbol appears on the display,
the keypad is locked.
Keypad unlock
To unlock the keypad, press the
for 10 seconds again. The padlock symbol
keypad is unlocked.
When keypad is locked, only the key
If the device is on Standby mode when the keypad is locked, you
have to unlock it for the next heating on to access the setup.
prog prog
boost
OK OK
see page 13 for more de-
1 2 3 4 5 6 7
for more than 5 seconds.
auto auto prog prog
3
mode mode
and buttons hold them down
disappears from the display,
is active.

7 DAY AND DAILY PROGRAMME

INTEGRATED, ENERGY SAVINGS
AUTOMATIC PROGRAMMING WITH SELF-
LEARNING PROCESS
Overview
Auto-programming (Auto): After an initial learning period of one week,
the device will analyze occupancy cycles to determine and implement
a weekly programme adapted to your lifecycle alternating periods in
comfort and periods in eco, the goal being to deliver the most efficient
yet comfortable and user focused heating cycle. The products algorithm
will perpetually learn and adapt to changes in your occupancy patterns,
adapting week after week to optimize the heating programme to any
changes in your evolving occupancy patterns.
Operating
Upon the first activation of your
device, the mode
gramme" is activated by default,
in mode Auto. To deactivate and
change the programme,
and affectation of programmes
page 8.
The first week of operation is a
learning week during which the
device memorizes your habits
and elaborates a program for the
week.
It therefore defines a programme
built up of periods of Comfort and
Eco, independently for each day of
the week.
During this learning week, the de-
vice will provisionally function in permanent "Comfort" mode.
Important:
To ensure the auto-programming is optimized, please en-
sure the presence detection sensor is not interrupted by an external
source, see important information concerning the presence detection
system on page 9.
Application of the intelligent program
One week after switching on, the device will apply the new program
for the next 7 days. Then week after week the device will continue to
optimize the intelligent program "Auto", adjusting the Comfort and Eco
periods to fit closely to your lifestyle.
When the product is in Frost protection mode or in standby mode for
more than 24 hours, learning and optimization of the intelligent pro-
gram stops: the device stores the previously recorded program from the
last week before switching to the Frost protection or standby mode.
- Example 1: If the product is installed in mid-season or if its installa-
tion is anticipated on the construction site, it can be switched on in
standby mode. When you select the Auto mode, the learning week
will start automatically. The device will be in permanent comfort
and will memorize your habits to apply the adapted program the fol-
boost
lowing week.
- Example 2: You select frost protection mode before going on holiday.
Upon your return, when you return to Auto mode, the unit will au-
tomatically apply the previously stored intelligent program from the
OK OK
last week before you left.
In the case of control by pilot wire coming from an energy manager for
example, the pilot wire will take precedence over the AUTO program
which results from the Self-learning algorythm.
auto auto
"auto-pro-
see choice
Example of display
in Comfort period
mode mode
auto auto
Example of display
in Eco period
mode mode
EN
prog prog
boo
3
OK OK
prog prog
boo
3
OK OK
5