IN & OUT HOUSE EF197A Instructions D'utilisation page 20

E N
S E T TI N G YO U R TA RG E T TE M PE R AT U R E
Press the '+' or '-' button to increase or decrease the temperature based on
the temperature setting you want.
• ECO means 2 °C lower than your desired temperature setting.
ECO – means 4 °C lower.
COMF+ means 2 °C higher.
COMF++ means 4 °C higher.
To check your daily timer settings, press
off, you need to return to normal mode to switch it off.
TI M E R FO R W E E K LY H E ATI N G
There are preset heating times that can be altered if desired.
From Monday to Friday 6:00 a.m. to 8:30 a.m., 5:00 p.m. to 10 p.m.
From Saturday to Sunday: 6:30 a.m. to 9:30 a.m, 11:00 a.m. to 1:00 p.m.,
5:00 p.m. to 10:00 p.m
Press M until is displayed in the upper right corner of the screen and then
enter the weekly timer heating mode. Press
seconds to activate the weekly timer.
• Press or to move the cursor (flashing under- underline)
• Press the button in the corresponding weekly position to select the
current setting (the symbol is highlighted) or to cancel (the symbol is
displayed normally). Several days can be selected together.
• Press the button to move the cursor to the setting area for the time
period. Press or to select hours or minutes. Press '+' or '-' to the
desired time.
• Maximum three heating periods per day
• Each time the button is pressed, the number of minutes is increased /
decreased by 15 minutes.
• Press the button to set the heating times for the selected day(s) and
return to the weekly over view.
• Press and hold the button for three seconds or wait 10 seconds to save
and exit the heating time setting. To check your weekly timer settings,
press the and button. If the heater is to be switched off, you must
return to normal control mode to switch it off.
38
. If the heater needs to be switched
and hold the button for six
E N
E X PA N D E D S E T TI N G S
In day and week mode, press . To switch off the heater when the heater is on
during a preset heating period. To switch on the heater when the heater is off
between preset heating times.
C U S TO M I S E D S TA R T-U P C O N T RO L
Depending on the room temperature and the target temperature, the heater
switches on automatically to heat the room to the set temperature at the set
time. For example, if your timer is set to 6:00 p.m. and the temperature is set
to 23 °C, the heater will switch on at 5:30 p.m. to ensure that the room is 23 °C
at 6:00 p.m.
O PE N W I N D OW D E T E C TI O N
If the transmit ter detects a rapid drop in room temperature, this is interpreted
as an open window. A warning symbol is displayed and the heater is auto -
matically switched off. Af ter the indoor temperature has risen or a manual
override of the warning has been made (by using the remote control), the unit
returns to normal operation.
R E S E T TI N G T H E T H E R M A L C U T O U T
The appliance is fitted with an Electronic Safety Control (E.S.). This is a
safety device, which switches off the fire if, for any reason, the appliance over-
heats, e.g. when covered. If the heater stops operating while the flame effect
continues working normally, this indicates that the E.S. Control is in operation.
The E.S. Control can only be re -set after the appliance has cooled down,
and the appliance has been reset. Re -setting of the E.S. Control proceeds is
as follows:
1. Switch off the appliance (Manual On / Off switch) and leave it off for
approximately 10–15 minutes.
2. Remove any obstruction to the fan heater outlet or fan blades etc.
Make sure that the power supply is disconnected with the plug socket
outlet while doing this.
3. Switch on the appliance and the E.S. Control will be re -set.
4. Ensure that the appliance is functioning correctly. If the E.S. Control
doesn' t operates again, the appliance should be checked by a
competent electrician.
39