Continuous Operation - Bosch GKP 200 CE PROFESSIONAL Instructions D'emploi

1 609 929 J27.book Seite 1 Mittwoch, 2. November 2005 10:09 10
Unit Specifications
Glue Gun
Order number
Rated power input
(heating up), approx. [W]
Rated power input
(maintaining heat),
approx. [W]
Gluing capacity [g/min] 30
Heating time, approx. [min]
Glue temperature [°C]
Glue stick diameter [mm]
Glue stick length [mm]
Weight without cable,
approx. [kg]
Protection class
Please observe the order number of your unit.
The trade names of the individual units may vary.
Unit Elements
1 Nozzle
2 Feed button
3 Charging station*
4 Mains indicator
5 Mains cable
* Not all of the accessories illustrated or described are
included as standard delivery.
Intended Use
The glue gun is intended for the quick gluing of
clean, dry and grease-free materials with glue
heated to its melting point.
For Your Safety
Working safely with this unit is
possible only when the operating
and safety information are read
completely and the instructions
contained therein are strictly fol-
lowed.
If the mains cable is damaged or separated dur-
ing work, do not touch the cable, but pull the
mains plug immediately. Never operate the unit
with the mains cable damaged.
Always guide the cable toward the rear away from
the unit.
Before each use of the unit, check the cable and
plug. If damage is detected, do not use the unit.
Have repairs performed only by a qualified tech-
nician. Never open the unit yourself.
6 • 1 609 929 J27 • TMS • 19.10.05
Danger of burning! The glue and the nozzle tip
are 200 °C hot. Do not allow glue to come into
contact with persons or animals. If glue comes in
GKP 200 CE
contact with the skin, immediately hold the spot
PROFESSIONAL
under a stream of cold water for some minutes.
0 601 950 7..
Do not try to remove the glue from the skin. Seek
medical advice if severe.
500
The unit must not be damp and must not be used
in a wet environment.
Children may operate the unit only under adult
30
supervision.
For pauses in the work of more than 30 minutes,
4
pull the mains plug.
200
Allow the unit to cool completely before storing.
11
The hot nozzle can cause damage.
45 – 200
Bosch is only able to ensure perfect operation of
the unit if the original accessories intended for it
0.4
are used.
/ II
Starting Operation
Observe correct mains voltage: The voltage of the
power source must agree with the voltage specified
on the nameplate of the unit. Equipment marked
with 230 V can also be connected to 220 V.

Continuous Operation

The hot glue gun can be operated continuously with
the mains plug inserted. The mains indicator 4 must
light up. During pauses in working, place the unit
down on the folded out wire stand.
Cordless Operation
In conjunction with the charging station 3 (acces-
sory), cordless working is possible. If the emerging
glue becomes viscous, the hot glue gun is to be re-
heated in the charging station.
Operating Instructions
Glue Temperature
The temperature of the surroundings and the work-
piece must be between 5 and 50 °C. Materials that
quickly cool the glue, e. g., metals, should be pre-
heated with a hot air gun.
Gluing
Rough up smooth surfaces before gluing. The gluing
spots must be dry and free of dust or grease.
Do not use combustible solvents for cleaning.
– Heat up the unit for approx. 4 minutes.
– Insert a glue stick.
– Press the feed button 2.
– Apply glue as required.
For the gluing of flexible materials (e. g. textiles), ap-
ply the glue in beads.
English - 1