Identification Number; Lock Function - IMG STAGELINE TXS-865HT Mode D'emploi

5.1.4 Automatic frequency matching
(REMOSET function)
To enable / disable the automatic frequency match-
ing (REMOSET function = frequency setting of the
transmitter via a radio signal of the receiver unit)
for the transmitter:
1) Keep the button SET (4) pressed until the display
briefly shows
mode (group indication starts flashing) .
2) Press the button SET repeatedly until the display
shows the current setting for the automatic fre-
quency matching:
automatic frequency matching enabled
(i . e . frequency setting of the transmitter
via the REMOSET function is possible)
automatic frequency matching disabled
(i . e . no REMOSET transmission)
3) Press the button  (3) to select the setting
or press the button  (5) to select the
setting .
4) Press the button SET to confirm . The display
briefly shows
the normal mode .

5.1.5 Identification number

To enable the REMOSET transmission between the
transmitter and the receiver unit, match their iden-
tification numbers .
1) Keep the button SET (4) pressed until the display
briefly shows
mode (group indication starts flashing) .
2) Press the button SET repeatedly until the display
shows and the current identification number
( ... or ) .
3) In the setting range
the button  (3) to search in descending order
or press the button  (5) to search in ascending
order . Use the corresponding arrow button to
set the transmitter to the identification number
of the receiver unit (the transmitter will only
respond to the REMOSET signal of this receiver
unit) or select
to the REMOSET signal of any receiver unit) .
4) Press the button SET to confirm . The display
briefly shows
normal mode .
All rights reserved by MONACOR
reproduced in any form or by any means for any commercial use.
and then the group setting
. The unit will then return to
and then the group setting
, ...
(the transmitter will respond
. The unit will return to the
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may be
®

5.1.6 Lock function

When the lock function has been activated, you will
no longer be able to switch off the microphone or
to mute it . From the setting modes, you will only
be able to activate the mode for the lock function
in order to deactivate the lock . When you press a
button, the display will show
Activating the lock
1) Keep the button SET (4) pressed until the display
briefly shows
mode (group indication starts flashing) .
2) Press the button SET repeatedly until the display
shows
3) To activate the lock, press the button  (5) . The
display shows
4) Press the button SET to confirm . The display
briefly shows
normal mode .
Deactivating the lock
1) Keep the button SET (4) pressed until
flashing in the indication
2) To deactivate the lock, press the button  (3) .
The display shows
3) Press the button SET to confirm . The display
briefly shows
normal mode .
6 Specifications
Carrier frequency range: 506 – 542 MHz
Frequency stability: . . . . ±0 .005 %
Transmission power: . . . switchable
Audio frequency range: 50 – 16 000 Hz
press
Microphone cartridge: . dynamic / cardioid
Ambient temperature: . 0 – 40 °C
Power supply: . . . . . . . . 2 × 1 .5 V battery of size
Operating time: . . . . . . > 25 h (for alkaline
Dimensions: . . . . . . . . . ⌀ 50 mm × 250 mm
Weight: . . . . . . . . . . . . 350 g
Subject to technical modification .
(lock on) .
and then the group setting
(lock off) .
.
. The unit will return to the
.
.
. The unit will return to the
☞ table on page 20
10 mW/ 50 mW
AA (not supplied)
batteries 3400 mAh)
starts
11