Maintenance And Service; Accessories; After-Sales Service And Application Service - Bosch GCO 2000 Professional Notice Originale

OBJ_BUCH-3061-001.book Page 20 Wednesday, December 14, 2016 1:05 PM
20 | English
Adjusting the Depth Stop (see figure H)
In the delivery condition of the machine, the depth stop 16 is
adjusted in such a manner that a new 355 mm cutting disc
does not touch the base plate when cutting.
To compensate the wear of the cutting disc, the depth stop
can be set deeper.
When using a new cutting disc, the depth stop must then al-
ways be set back to the original position.
 Always adjust the depth stop in such a manner that the
cutting disc does not touch the base plate when cut-
ting.
– Bring the power tool into the working position. (see "Re-
leasing the Machine (Working Position)", page 18)
– Loosen lock nut 25 with the supplied ring spanner 14
(13 mm).
– Swing the tool arm with the handle 3 to the requested po-
sition.
– Screw the depth stop 16 in clockwise or anticlockwise di-
rection until the screw head touches the housing.
– Slowly guide the tool arm upward and tighten the lock nut
25.
Transport
– Always carry the power tool by its transport handle 18.
 When transporting the power tool, use only the trans-
port devices and never use the protective devices.

Maintenance and Service

Maintenance and Cleaning
 Before any work on the machine itself, pull the mains
plug.
 Clean the ventilation slots of your power tool regularly
with a soft brush. The motor fan draws dust into the hous-
ing, and a large accumulation of metal dust can lead to
electrical hazards.
 In extreme conditions, always use dust extraction as
far as possible. Blow out ventilation slots frequently
and install a portable residual current device (PRCD).
When working metals, conductive dust can settle in the in-
terior of the power tool. The total insulation of the power
tool can be impaired.
 Have maintenance and repair work performed only by
qualified specialists. In this manner, it can be ensured
that the safety of the power tool is maintained.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
The retracting blade guard must always be able to move freely
and retract automatically. Therefore, always keep the area
around the retracting blade guard clean.
1 609 92A 342 | (14.12.16)

Accessories

Cutting disc

After-sales Service and Application Service

In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0844) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
Article number
2 608 600 543
Bosch Power Tools