Makita DUB143 Manuel D'instructions page 12

Masquer les pouces Voir aussi pour DUB143:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 14
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will also
void the Makita warranty for the Makita tool and charger.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the
battery cartridge when you notice less tool
power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge
the
battery
temperature at 10 °C – 40 °C (50 °F – 104 °F).
Let a hot battery cartridge cool down before
charging it.
4. Charge the battery cartridge if you do not use it
for a long period (more than six months).
FUNCTIONAL DESCRIPTION
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before adjusting or
checking function on the tool.
Installing or removing battery cartridge (Fig. 1)
CAUTION:
• Always switch off the tool before installing or removing
of the battery cartridge.
• Hold the tool and the battery cartridge firmly when
installing or removing battery cartridge. Failure to
hold the tool and the battery cartridge firmly may cause
them to slip off your hands and result in damage to the
tool and battery cartridge and a personal injury.
To remove the battery cartridge, slide it from the tool while
sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place with
a little click. If you can see the red indicator on the upper
side of the button, it is not locked completely.
CAUTION:
• Always install the battery cartridge fully until the red
indicator cannot be seen. If not, it may accidentally fall
out of the tool, causing injury to you or someone around
you.
• Do not install the battery cartridge forcibly. If the
cartridge does not slide in easily, it is not being inserted
correctly.
12
cartridge
with
room
Indicating the remaining battery capacity (Fig. 2)
(Only for battery cartridges with "B" at the end of the
model number.)
Press the check button on the battery cartridge to indicate
the remaining battery capacity. The indicator lamps light
up for few seconds.
Indicator lamps
Lighted
Off
Blinking
015658
NOTE:
• Depending on the conditions of use and the ambient
temperature, the indication may differ slightly from the
actual capacity.
Switch action (Fig. 3)
CAUTION:
• Before inserting the battery cartridge into the tool, always
check to see that the switch trigger actuates properly
and returns to the "OFF" position when released.
To start the tool, simply pull the switch trigger. Air volume
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
Air volume adjusting dial
Air volume can be adjusted to any of three settings by
turning the adjusting dial with the switch trigger fully
depressed. Refer to the table below for the relationship
between the number on the dial and the air volume.
Number on the dial
3
2
1
008312
CAUTION:
• Use the adjusting dial only after the switch trigger
returns to the "OFF" position. Turning the dial before
the trigger returns may damage the tool.
• If the tool is operated continuously until the battery
cartridge has discharged, rest the tool for at least
15 minutes before proceeding with a fresh battery.
Remaining capacity
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the battery.
The battery may have
malfunctioned.
Air volume
High
Medium
Low

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Dub183

Table des Matières